2
3402011100_31-P5711G
105 × 148 mm
Wireless doorbell P5710G-2T
The digital doorbell set consists of two bell pushbuttons (TX) and the bell unit (RX). The bell unit has to be permanently connected to electric
network (230V AC/50 Hz). The transmission between the pushbutton and the bell unit is based on radio waves on frequency 433,92MHz.
Transmission range is up to 100m in open area, depending on the conditions.
Please read the following user manual carefully.
Technical specification
Transmission range:
up to 100 m in open area
Waterproof pushbutton:
with IP44 coverage
Pairing method:
self-learning function
Possibility to pair more pushbuttons: yes (max 3)
Number of melodies:
3 – possibility to set different melody for more pushbuttons (max 3) used
Power of bell unit:
230V AC/50Hz
Power of pushbutton:
1× 12V battery (type A23)
Packaging includes:
Double side sticker
The wireless digital door chime has self-learning function for pairing with pushbuttons. Therefore it is possible to combine with additional
pushbuttons. The advantage of this type of pairing is prevention from other chimes in the neighborhood.
Pairing of bell unit with pushbutton
1. Remove the back casing of the pushbutton through the hole in the side of the casing with a screwdriver. Insert 1pc of 12V battery (type
23A) according to the polarity indicated.
2. Press the button “SW2” on the printed circuit board once – signaling LED of transmitter turns on for 5 seconds. Within these 5 seconds,
press the button “SW2” once again - signaling LED blinks three times meaning, that new code was generated.
3. Reassemble the pushbutton casing.
4. If you need to pair more pushbuttons, repeat points 1. – 3. for each pushbutton.
5. Plug in the bell unit (RX), the learning mode is entered automatically for two minutes and signaling LED on bell unit blinks.
6. Within these two minutes press the desired pushbutton, if bell unit receives TX signal, it will play the melody corresponding to which
selected at pushbutton (TX).
7. If you need to pair more pushbuttons, repeat point 6. also for other pushbuttons.
Note: In case of power down of bell unit, it contains built-in memory, which is used for storing of actually learned codes. When the power is on
again, the learning mode is entered automatically for 2 minutes. If no new pairing is made within these 2 minutes, bell unit loads previously
learned codes afterwards. When the power down happens, there is no need to proceed new pairing.
SW2
choice of melody
Choice of melody
Melody can be changed anytime. It won’t affect communication between paired bell unit and pushbutton.
1. Remove the back casing of the pushbutton through the hole in the side of the casing with a screwdriver.
2. There are 3 pins with jumper on the printed circuit board. Choose one of three melodies with:
- connecting pins 1 and 2
- connecting pins 2 and 3
- removing the jumper (no pins are connected)
3. Reassemble the pushbutton casing.
Pushbutton installation
1. Firstly proceed the pairing of bell unit with pushbutton.
2. Before you start mounting, make sure that the chime works properly on the place you have chosen.
3. Remove the back casing of the pushbutton through the hole in the side of the casing with a screwdriver.
4. Place this back casing outside your home. Use double side sticker (included) or screws to fix it on the wall. Although the pushbutton is
waterproof, it is better to place it under the shelter.
5. Reassemble the pushbutton casing.
6. Press the button, signaling LED on the pushbutton indicates that radio signal was transmitted. Bell unit sounds chosen melody.
7. If the signaling LED does not light, battery is flat, please replace it. Battery usually last for one year but it may differ according to conditions.
Note: The pushbutton unit can be placed on wooden or brick walls, however, do not place it on metal surfaces or surfaces containing metal.
It might affect the correct function of the unit.
Bell unit installation
1. The bell unit (RX) is designed for inner use. It has to be plugged in a socket (230V AC/50Hz) and have open area around when operating.
2. The transmission range is up to 100 meters depending on the surroundings (number of walls, metal frames of doors, etc.)
GB
