Emerson TopWorx 4310 Скачать руководство пользователя страница 2

Страница: 2 / 24

4310 Wireless Position Monitor

Instruction Manual

October 2009

Table 1. Specifications

Available Mountings

Quarter

−

turn rotary

−

shaft,

sliding

−

stem or

linear applications

Can also be mounted on other actuators that
comply with IEC 60534

−

1, IEC 60534

−

VDI/VDE 3845 and NAMUR mounting standards.

Input Measurement

Stem Travel

Minimum: 12.5 mm (0.49 inch)
Maximum: 102 mm (4 inches)

Shaft Rotation

Minimum: 45

Maximum: 90

Measurement Output

Discrete: on/off switches (2)

Local User Interface

Liquid Crystal Display (LCD)
Two pushbuttons for navigation, setup, and
calibration

Input Communication Signal

WirelessHART

communication

HART Variables

Variable

Variable Name

Primary (PV)

not used

Secondary (SV)

Closed Trigger

Tertiary (TV)

Open Trigger

Quaternary (QV)

Internal Temperature

Variable #5

Power Module Voltage

Output Communication Signal

2.4 GHz, DSSS, WirelessHART
Maximum 10 dBm EIRP at 2.46 GHz,
10 mW EIRP at 2.46 GHz

Wireless Classifications

Class A digital device, complies with part 15 of the
FCC Rules
Contains FCC ID: LWZRM2510
Contains IC: 2731A

−

RM2510

Electromagnetic Compatibility

Meets EN 61326-1 (First Edition)

Immunity—Industrial locations per Table 2 of

the EN 61326-1 standard. Performance is
shown in table 2 below.

Emissions—Class A & B. Performance is

shown in table 3 below

ISM equipment rating:

Group 1, Class A & B

Operating Temperature Limits

(1,2)

−

40 to 80

C (

−

40 to 176

LCD may not be readable below

−

C (

−

Temperature Sensitivity

0.05% change per degree C

Storage Temperature Limits

(1,2)

Upper limit not to exceed 100

C (212

Humidity Limits

−

95% RH

Electrical Housing

IP66; third party approval pending

(3)

IEC 61010 Compliance

Meets Pollution Degree 2

Adjustments

Zero and Maximum Span through local interface.

Weight

0.5 Kg (1.1 lbs)

Power Module

(2)

Standard

Lithium, non

−

rechargeable

−

continued

−

Содержание TopWorx 4310

























Результаты поиска

Содержание TopWorx 4310

Отзывы:

Похожие инструкции для TopWorx 4310

Бренды по названию

Популярные бренды

Emerson TopWorx 4310, Инструкция по эксплуатации

Результаты поиска

Содержание TopWorx 4310

Отзывы:

Похожие инструкции для TopWorx 4310

Бренды по названию

Популярные бренды