background image

12

U.L. Model No.: CF3300

IMPORTANT CARE INSTRUCTIONS

for your Ceiling Fan

Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.

When cleaning, use only a soft brush or lint free cloth
to avoid scratching the finish.

Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.

Maintenance

Accessories

1.

Ceiling Fan Light Kits (see store or catalog).

2.

Ceiling Fan/Light Controls (see store or catalog).

3.

Downrod Extension Kits (see store or catalog).

Do not use water when cleaning your ceiling
fan. It could damage the motor or the blades
and create the possibility of an electrical shock.

WARNING

!

This product is designed to use only those
parts supplied with this product and/or any
accessories designated specifically for use
with this product by Emerson Electric Co.
Substitution of parts or accessories not
designated for use with this product by
Emerson Electric Co. could result in personal
injury or property damage.

The use of any other control not specifically
approved for this fan could result in fire, shock
and personal injury.

WARNING

!

WARNING

!

AIR DIRECTION SWITCH 
(1 switch located on each 
fan housing)

FAN HOUSING

Figure 21

Reversing Air Flow Direction:

7

If airflow is desired in the opposite direction, turn
the fans off at wall control and wait for the blades
to stop turning. Then slide the reversing switches,
located on both housings, to the opposite position
(Figure 21) and turn the fan on again. The blades
will turn in the opposite direction and reverse the
airflow.

Содержание ST CROIX CF3300AP

















Отзывы: