background image

U.L. Model No.: CF3300

How to Put Your Ceiling Fan Together

HAIRPIN 
CLIP

CLEVIS PIN

DOWNROD 
COUPLING

DOWNROD 
EXTENSION

5/16-18 x 1/4" CUP 
POINT SETSCREW (2)

Figure 1

4

OFF

K. HANGER BRACKET 

ASSEMBLY

M. SW22 
WALL 
CONTROL

A. FAN  
ASSEMBLY

B. FAN MOTOR 
COVERS (2)

H. RIGHT HAND 
BLADE FLANGES (4)

C. DECORATIVE DOWNROD 

SLEEVE ASSEMBLY

G. CEILING 
CANOPY

M. MOUNTING 
BRACKET BAG

N. HARDWARE 
BAG

O. FLANGE 
ASSEMBLY 
BAG

P. BLADE 
ASSEMBLY 
BAGS

Q. DOWNROD 
ASSEMBLY 
BAG

F. DECORATIVE 
STRAP RING

D. UPPER 
DECORATIVE 
DOWNROD SLEEVE

I.

 LEFT HAND BLADE 

FLANGES (4)

L. BLADE 
MEDALLIONS (8)

E. DOWNROD 
EXTENSION

J. HANGER BALL/
DOWNROD 
EXTENSION

1.

Loosely install both 5/16-18 x 1/4” cup point
setscrews (supplied) into the downrod coupling.
Separate, untwist and unkink the three 80” motor
leads and support wire. Route the motor lead wires
and support wire through the downrod extension.
Align the clevis pin holes in the downrod extension
with the holes in the downrod coupling. Install the
clevis pin and secure with the hairpin clip
(Figure 1). The clevis pin must go through the
holes in the downrod coupling and the holes in the
downrod extension. Be sure to push the straight leg
of the hairpin clip through the hole near the end of
the clevis pin until the curved portion of the hairpin
clip snaps around the clevis pin. The hairpin clip
must be properly installed to prevent the clevis pin
from working loose. Pull on the downrod extension
to make sure the clevis pin is properly installed.

2.

While pulling up on the downrod extension,
securely tighten the two setscrews in the downrod
coupling using the 3/16” hex wrench (supplied).
The setscrews must be tightened into the downrod
extension. A loose extension downrod will result
with fan assembly noise and vibration.

It is critical that the clevis pin in the downrod
coupling is properly installed and the
setscrews securely tightened. Failure to verify
that the pin and setscrews are properly
installed (as shown in Figure 1) could result in
the fan falling.

WARNING

!

NOTE: For ease of installation, loosely tape the
ends of the motor leads and the support wire
together to route through downrod during fan
installation.

3.

Route the motor leads and support wire through
the downrod (Figure 2).

4.

Securely attach the downrod to the downrod
extension using the four 1/4 x 10mm round head
screws (supplied in the downrod assembly bag).
The round head screws must be fully tightened into
the downrod extension. A loose downrod will result
with fan assembly noise and vibration.

Содержание ST CROIX CF3300AP

















Отзывы: