Emerson Rosemount SOLU COMP II Скачать руководство пользователя | Manualshive

Страница: 49 / 58

background image

41

8.2.2 RTD for Sensor 1 is Open or Shorted.

There is an open or short in the sensor RTD or wiring.

A. If sensor is being installed for the first time, check the wiring connections. See Section 3.2.

B. Disconnect the sensor from the analyzer and measure the resistance between the RTD lead wires. See the

sensor manual to identify the RTD leads. If there is an open or short circuit, replace the sensor.

C. If there is no open or short, check the analyzer. See Section 8.5.

MODEL SOLU COMP II

SECTION 8.0

TROUBLESHOOTING

SECTION 8.0

TROUBLESHOOTING

8.1 OVERVIEW
8.2 TROUBLESHOOTING USING FAULT CODES
8.3 TROUBLESHOOTING WHEN NO ERROR MESSAGE IS SHOWING — OZONE
8.4 TROUBLESHOOTING WHEN NO ERROR MESSAGE IS SHOWING — GENERAL
8.5 SIMULATING INPUTS
8.6 SIMULATING TEMPERATURE

8.1 OVERVIEW

The Solu Comp II continuously monitors itself and the sensor for faults. When the analyzer detects a fault, the
word

fault

appears in the display alternately with the measurement. If alarm 3 was configured as a fault alarm,

the alarm relay will energize. The outputs do not change during a fault condition. They continue to reflect the
measured ozone or temperature.

Press

"

to display the fault codes.

NOTE

A large number of information screens are available to aid troubleshooting. The most useful of these are
raw sensor current and sensitivity and zero current at last calibration. To view the information screens,
go to the main display and press the

'

key.

8.2 TROUBLESHOOTING USING FAULT CODES

8.2.1 Sensor Current Exceeds 210

µµ

A

Excessive sensor current implies that the sensor is miswired or the sensor has failed.

Fault Code

Explanation

See Section

S1 Out of Range

Sensor current exceeds 210

µ

A

8.2.1

TC1 Open

RTD for sensor 1 (ozone) is open

8.2.2

TC1 Shorted

RTD for sensor 1 (ozone) is shorted

8.2.2

S1 Sense Line Open

RTD sense line for sensor 1 (ozone) is open

8.2.3

EEPROM Failure

EEPROM failure

8.2.4

«
...
47
48
49
50
51
...
»

Содержание Rosemount SOLU COMP II



























































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount SOLU COMP II

Бренд: BANTE inststruments Страницы: 15

Бренд: 3Bays Страницы: 21

LaserRange-Master T4 Pro

Бренд: LaserLiner Страницы: 68

DC1500 CHLORINE

Бренд: LaMotte Страницы: 60

Бренд: QuadTech Страницы: 76

Бренд: Velleman Страницы: 96

Electone B-20CR

Бренд: Yamaha Страницы: 16

Бренд: Ansul Страницы: 24

Бренд: ENDA Страницы: 2

Бренд: Heinrichs Страницы: 31

Бренд: OmegaWatt Страницы: 9

Engine Analyzer Series

Бренд: ACCEL DFI Страницы: 39

Бренд: HTC Страницы: 2

efector300 SM0510

Бренд: IFM Electronic Страницы: 45

Бренд: Hantek Страницы: 40

Бренд: Opsytec Страницы: 37

28APE190008/AI481

Бренд: Apera Instruments Страницы: 13

Бренд: Falcon Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды