Emerson Rosemount Analytical CAT 100 Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 122

background image

Instruction Manual

748441-D

April 2002

Rosemount Analytical Inc. A Division of Emerson Process Management

Maintenance and Service 5-3

Model CAT100

a. Analyzer

Removal

1. Refer to drawing 659921 for location

of components.

2. Remove only the dome housing from

the extender ring.

3. Mark the location of the screws on

each analyzer mount using a fine tip
marker. It is important that the ana-
lyzer be replaced in the exact same
location so that the light guides touch
the inside of the glass window.

4. Loosen, do not remove, the screws

(17) holding the swing tab (14) on
each analyzer mount (2) and swing
the tab clear of the slot.

5. Loosen, do not remove, the six

screws (23) holding the analyzer.

6. Slide the analyzer forward being care-

ful of the umbilical cables and gas
lines attached.

7. Disconnect all electrical connections

and gas lines and remove the ana-
lyzer component for repair or re-
placement.

8. Close all gas line fittings with PVC

caps after removal of the analyzer.

b. Analyzer

Replacement

1. Slide the analyzer onto the mounts,

being careful that the screws and
washers are on the outside.

2. Locate the analyzer in the exact same

location as when removed by aligning
the screws with the alignment marks
previously made.

3. Tighten

the

screws.

4. Make sure the dome threads are

clean and free of any contaminants.

5. Replace the dome housing, by lining

up the reference marks so that the
threads engage properly. If any resis-
tance is felt, remove the dome and
clean the threads.

6. Make sure that the spring loaded light

guides just touch the inside of the
glass window. Failure to have the light
guides touching the glass window can
result in spontaneous menu naviga-
tion.

c.

Power Supply Assembly Removal

1. Follow the process for analyzer re-

moval in Section 5-2a (page 5-3).

2. Disconnect all wires from the power

supply terminal block.

3. Loosen, do not remove, the three

screws (17) holding the power supply
assembly.

4. Slide the power supply assembly in its

slotted holes and remove.

5. Reverse the process for installation.

«
...
69
70
71
72
73
...
»

Содержание Rosemount Analytical CAT 100



























































































































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount Analytical CAT 100

DigitalFlow GF868

Бренд: GE Страницы: 80

Бренд: Valeport Страницы: 25

Бренд: Keithley Страницы: 201

Бренд: Oakton Страницы: 16

Бренд: +GF+ Страницы: 64

Бренд: +GF+ Страницы: 12

Бренд: +GF+ Страницы: 48

Бренд: Hama Страницы: 16

Бренд: YOSensi Страницы: 27

Бренд: WIKA Страницы: 88

WM14-96 - PROGRAMMING

Бренд: CARLO GAVAZZI Страницы: 6

Бренд: Omicron Страницы: 76

Бренд: Galileo Страницы: 30

WARREN ELLIS SIGNATURE TENOR BARITONE

Бренд: Eastwood Guitars Страницы: 4

Бренд: Fluke Страницы: 32

Бренд: Vector Страницы: 8

Бренд: PCE Instruments Страницы: 20

Roast Alert/3 ET-8C

Бренд: Redi-Chek Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды