Emerson Rosemount Analytical CAT 100 Скачать руководство пользователя страница 109

Страница: 109 / 122

Instruction Manual

748441-D

April 2002

Rosemount Analytical Inc. A Division of Emerson Process Management

Troubleshooting 6-3

Model CAT100

Error Code

Possible Reasons

Check / Remedy

1. Measuring range failure.

Pressure not ins the sensor measuring

range. (800 – 1100 hPa)

2. Connection

faulty.

Check connection P1 for pressure

sensor at BAF01. See Section 5-5a,
page 5-29.

Pressure sensor defective

3. Pressure sensor faulty.

Change pressure sensor.

1. EPROM

faulty.

Exchange EPROM. See Section 5-4o,
page 5-28.

EPROM checksum failure

2. BKS PCB faulty.

Exchange BKS PCB.

Test for RAM defective

1. RAM IC’s on BKS PCB faulty.

Exchange BKS PCB.

Analog output absent

1. BKS PCB faulty.

Exchange BKS PCB.

1. Leakage into gas circuit.

Perform a leakage check. See Sections

2-3 (page 2-11) and 6-2 (page 5-6).

2. Ambient air contains gas

constituent to be measured in
excessive concentration.

Replace absorber material for the light

sources and chopper housing.
Use sealed photometer option.
Flush out the analyzer.

3. Gas pressure subject to

excessive fluctuations.

Check the gas line preceding and

following the sensor cell.
Eliminate any restrictions found beyond
the gas outlet fitting.
Reduce pumping rate or flow rate.

4. Oxygen

sensor

not

connected.

Check connections:

BKS PCB X5 oxygen sensor channel 1.
BKS PCB X6 oxygen sensor channel 2.

5. Electrochemical

oxygen

sensor is already consumed.

Replace sensor. See Section 5-4j, page

5-21.

Fluctuating or erroneous

display

6. IR Channel light source not

connected or faulty.

Check connection:

BKS PCB X3(1/2) light source ch. 1.
BKS PCB X3(4/5) light source ch. 2.
Light source is cold:
For dual infrared channel analyzer,
exchange the two light sources.
Replace the suspected light source. See
Section 5-4d, page 5-18.

Содержание Rosemount Analytical CAT 100



























































































































Результаты поиска

Содержание Rosemount Analytical CAT 100

Отзывы:

Похожие инструкции для Rosemount Analytical CAT 100

Бренды по названию

Популярные бренды

Emerson Rosemount Analytical CAT 100, Инструкция по эксплуатации

Результаты поиска

Содержание Rosemount Analytical CAT 100

Отзывы:

Похожие инструкции для Rosemount Analytical CAT 100

Бренды по названию

Популярные бренды