Emerson Rosemount Analytical CAT 100 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 122

background image

Instruction Manual

748441-D

April 2002

Rosemount Analytical Inc. A Division of Emerson Process Management

Preface P-3

Model CAT

100

WARNING: TOXIC GAS

DANGER

.

TOXIC GAS

This device may contain explosive, toxic or unhealthy gas components. Before cleaning or chang-
ing parts in the gas paths, purge the gas lines with ambient air or nitrogen.

This unit’s exhaust may contain hydrocarbons and other toxic gases such as carbon monoxide.
Carbon monoxide is highly toxic and can cause headache, nausea, loss of consciousness, and
death.

Avoid inhalation of the exhaust gases at the exhaust fitting.

Connect exhaust outlet to a safe vent using stainless steel or Teflon line. Check vent line and con-
nections for leakage.

Keep all tube fittings tight to avoid leaks. See Sections 2-3 (page 2-11) and 6-2 (page 5-6) for leak
check information.

WARNING

.

HAZARDOUS AREA CERTIFICATION(S)

Any addition, substitution, or replacement of components installed on or in this device, must be
certified to meet the hazardous area classification that the device was certified to prior to any such
component addition, substitution, or replacement. In addition, the installation of such device or
devices must meet the requirements specified and defined by the hazardous area classification of
the unmodified device. Any modifications to the device not meeting these requirements, will void
the product certification(s).

WARNING

.

PARTS INTEGRITY AND UPGRADES

Tampering with or unauthorized substitution of components may adversely affect the safety of this
instrument. Use only factory approved components for repair.

Because of the danger of introducing additional hazards, do not perform any unauthorized modifi-
cation to this instrument.

Return the instrument to a Rosemount Analytical Service office for service or repair to ensure that
safety features are maintained.

«
...
9
10
11
12
13
...
»

Содержание Rosemount Analytical CAT 100



























































































































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount Analytical CAT 100

Бренд: Oceanic Страницы: 152

Бренд: Kaiterra Страницы: 8

Бренд: Kaiterra Страницы: 12

Бренд: Yamaha Страницы: 17

Бренд: Yamaha Страницы: 23

Бренд: Yamaha Страницы: 16

Бренд: Yamaha Страницы: 28

Бренд: Yamaha Страницы: 19

Бренд: Yamaha Страницы: 57

Clavinova CVP-204

Бренд: Yamaha Страницы: 56

disklavier Mark III Series

Бренд: Yamaha Страницы: 50

Бренд: Yamaha Страницы: 23

Бренд: PCB Piezotronics Страницы: 17

Бренд: Danfoss Страницы: 16

Бренд: Ibravebox Страницы: 32

Бренд: Suaoki Страницы: 79

Бренд: Carman Страницы: 64

SI Analytics Lab 855

Бренд: Xylem Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды