manualshive.com logo in svg

Emerson Rosemount 6888C, Инструкция по эксплуатации

Поделиться
Скачать
Emerson Rosemount 6888C Скачать руководство пользователя страница 69

Replacement screws are provided if any become lost or damaged.

9. Reconnect the power and signal wires to the transmitter board.
10.Reinstall the cover to the DR probe housing.
11.Reapply power to the DR probe.

8.3.4

Heater strut replacement

This section covers heater strut replacement. Do not attempt to replace the heater strut
until all other possibilities for poor performance have been considered.

If heater strut replacement is needed, order a replacement heater strut kit (

Table 9-1

 on

page 79). Refer to 

Figure 8-3

 on page 70 for item letter references.

 WARNING

BURNS
Use heat resistant gloves and clothing when removing probe. Do not attempt to work on
the probe until it has cooled to room temperature. The probe can be as hot as 427 °C (800
°F). This can cause severe burns.

Instruction Manual 

Maintenance and service

00809-0100-4891

July 2018

Instruction Manual 

69

Содержание Rosemount 6888C

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды