Emerson Rosemount 6888C страница 21 Скачать руководство пользователя | Manualshive

Страница: 21 / 88

background image

4

Install

WARNING

Before installing this equipment, read the Essential Instructions at the front of this
Reference Manual. Failure to follow safety instructions could result in serious injury or
death.

WARNING

ELECTRIC SHOCK
Install all protective equipment covers and safety ground leads after installation. Failure to
install covers and ground leads could result in serious injury or death.

4.1

Mechanical installation

Most combustion processes run only slightly negative or positive in pressure, so that the
probe flange is for mechanical mounting only. The probe is not rated for high pressures. If
this is a new installation, a

weld plate

for welding to the flue gas duct can be supplied.

WARNING

ELECTRIC SHOCK
Install all protective equipment covers and safety ground leads after installation. Failure to
install covers and ground leads could result in serious injury or death.

4.2

Mounting the Rosemount 6888 Xi General
Purpose Advanced Electronics

Follow the steps below to mount the Rosemount 6888 Xi.

The Rosemount 6888 Xi Advanced Electronics is available in a panel mounting or wall/pipe
mounting configuration. Refer to

Figure 4-1

or

Figure 4-2

for the panel, wall, or pipe

mounting details. The Rosemount 6888 Xi is rated for use in general purpose locations
only.

Ensure all components are available to install the Rosemount 6888 Xi.

1. Select a mounting location near or removed from the O

2

Probe.

Consider the temperature limitations of the Rosemount 6888 Xi (see

Rosemount 6888

Xi ambient temperature limits

) when selecting the mounting location.

2. Mount the Roseount 6888 Xi at a height convenient for viewing and operating the

interface.
Approximately 5 ft (1.5 m) is recommended.

3. The keypad window on the Rosemount 6888 Xi may have interior and exterior

protective membranes. Remove the protective membranes prior to use of the
Rosemount 6888 Xi enclosure.

Instruction Manual

Install

00809-0100-4891

July 2018

Instruction Manual

21

«
...
19
20
21
22
23
...
»

Содержание Rosemount 6888C

























































































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount 6888C

Бренд: Panasonic Страницы: 72

KW9M Eco-Power Meter

Бренд: Panasonic Страницы: 2

Бренд: Olympus Страницы: 362

Бренд: Olympus Страницы: 8

Бренд: Parkside Страницы: 114

Бренд: RADWAG Страницы: 12

Бренд: YOSensi Страницы: 27

Бренд: OHAUS Страницы: 84

Бренд: Hach Страницы: 4

Бренд: S&T Страницы: 23

Бренд: Mid-West Страницы: 14

Бренд: Geokon Страницы: 19

Бренд: Magneti Marelli Страницы: 20

Бренд: ProDetec Страницы: 49

Бренд: heinrichs weikamp Страницы: 56

IMI SENSORS 627A71

Бренд: PCB Piezotronics Страницы: 19

Бренд: Jula Страницы: 17

Бренд: Traveler Guitar Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды