Emerson Rosemount 6888C Скачать руководство пользователя страница 66

Страница: 66 / 88

Figure 8-1: Transmitter board mounting

A. Cover
B. Plastic cover
C. Transmitter board
D. Mounting plate
E. Screws
F. Thermal pad
G. Screws

1. Remove cover (A) from the transmitter housing.
2. Disconnect the power and signals from the transmitter board (C).
3. Remove the three screws (E) securing the plastic cover (B) and transmitter board (C) to

mounting plate (D).

4. The plastic cover snaps onto the transmitter board with three tabs. Pull the cover and

board away from the mounting plate.
The thermal pad (F) will most likely remain attached to the mounting plate.

5. Disconnect the two wire harness connectors from the back of the transmitter board

and remove the plastic cover and transmitter board.
Replacement transmitter boards come in two configurations:

a. Transmitter board with thermal pad and mounting screws
b. Transmitter board, thermal pad, plastic cover, mounting plate, and mounting

screws

6. If only the transmitter board is being replaced, carefully unsnap the plastic cover from

the old transmitter board and then snap it onto the new board.

Maintenance and service

Instruction Manual

July 2018

00809-0100-4891

6888C

Содержание Rosemount 6888C

























































































Результаты поиска

Содержание Rosemount 6888C

Отзывы:

Бренды по названию

Популярные бренды

Emerson Rosemount 6888C, Инструкция по эксплуатации

Результаты поиска

Содержание Rosemount 6888C

Отзывы:

Бренды по названию

Популярные бренды