background image

3. Ceiling Fan Assembly

(Continued)

CLEVIS
PIN

4.5"
DOWNROD

MOTOR
COUPLING

HAIRPIN
CLIP

CLEVIS
PIN

LOOSEN
SETSCREWS (2)

HAIRPIN
CLIP

Figure 8

3.11

Loosen the two setscrews in the motor coupling. 

Place  the  4.5”  downrod  into  the  motor  coupling,  aligning
the  clevis  pin  holes  in  the  downrod  with  the  holes  in  the
motor coupling (Figure 8).

The  clevis  pin  must  go  through  the  holes  in  the  motor
coupling and the holes in the downrod. 

Be sure to push the straight leg of the hairpin clip through
the  hole  near  the  end  of  the  clevis  pin  until  the  curved
portion of the hairpin clip snaps around the clevis pin. 

The  hairpin  clip  must  be  properly  installed  to  prevent  the
clevis pin from working loose. 

Pull on the downrod to make sure the clevis pin is properly
installed.

8

                                                                                                                                                                                                                              

ETL Model No.: CF965

It is critical that the setscrews are securely tightened.

Failure to verify that the setscrews are properly installed

could result in the fan falling.

                           

WARNING

!

RETIGHTEN

SETSCREWS

4.5" DOWNROD

MOTOR

COUPLING
RETIGHTEN

SETSCREWS

3.12

While  pulling  up  on  the  4.5”  downrod,  retighten  the  two
setscrews  (previously  loosened)  in  the  motor  coupling  to
secure the downrod into place (Figure 9).

NOTE: The setscrews must be properly installed as

described above, or fan wobble could result.

Figure 9

4.5" DOWNROD

COUPLING
COVER

MOTOR
HOUSING

COUPLING COVER
GROMMET

Figure 10

3.13

Make  sure  the  grommet  is  properly  installed  in  the
coupling  cover  then  slide  the  coupling  cover  on  the
downrod until it rests on the motor housing (Figure 10).

Be sure the motor coupler cover is oriented correctly.

It is critical that the clevis pin in the motor coupling is

properly installed. Failure to verify that the pin is properly

installed could result in the fan falling.

                           

WARNING

!

Содержание Portland CF965BS00

































Отзывы: