Emerson PACSystems Versamax Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 53

background image

User Manual

Chapter 1

GFK-2721B

Sep 2019

Introduction

7

1.3.3

Ethernet Network Ports

The two external Ethernet ports are on the bottom of the module. The illustration below is a
bottom view of IC200PNS001 with its two RJ-45 ports

Figure 4: Bottom view of IC200PNS001 with two RJ-45 Ports

Model  IC200PNS001  has  two  RJ-45  ports,  providing  10/100  Mbps  copper  interfaces.    Model
IC200PNS002 has two SC-Duplex ports, providing 100Mbps Multi-Mode fiber interfaces.  Each
Ethernet  port  automatically  senses  the  type  of  network  and  adjusts  speed  and  connection
parameters. The PROFINET Scanner requires at least one network be operating at full duplex for
a connection to remain established. The PROFINET protocol may be sent and received over either
or both two external ports.

Devices  connected  to  the  PROFINET  Scanner  ports  should  have  Ethernet  Autonegotiation
enabled  unless  the  IO-Controller  supports  configuring  the  port  operation  mode.  If  the  IO-
Controller  configures  the  PROFINET  Scanner  port  to  a  specific  setting  with  autonegotiation
disabled, the device connected to the PROFINET Scanner must be configured for the exact same
setting.

CAUTION

Both ports on the Ethernet Interface must not be connected, directly or indirectly, to the same
device to form a circular network unless Media Redundancy is enabled with one node actively set
up as the Media Redundancy Manager.

«
...
9
10
11
12
13
...
»

Содержание PACSystems Versamax






















































Отзывы:

Нет отзывов

Похожие инструкции для PACSystems Versamax

Бренд: Keithley Страницы: 36

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Raytech Страницы: 21

Бренд: Teac Страницы: 2

Бренд: laerdal Страницы: 2

Бренд: CAIRE Страницы: 2

Бренд: TAIKO Audio Страницы: 24

Бренд: Bard Страницы: 144

Бренд: GALBIATI Страницы: 8

Бренд: Vahva Jussi Страницы: 9

Бренд: xsto Страницы: 76

Бренд: F&V Страницы: 5

Бренд: F Care Systems Страницы: 2

MET ONE 3400 Series

Бренд: Hach Страницы: 48

Бренд: Latham Страницы: 4

Бренд: SafeWaze Страницы: 23

Life/form SmartScope LF01142U

Бренд: Nasco Страницы: 2

Smart Plus PHT-35LHS

Бренд: Vatech Страницы: 190

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды