background image

22. Connect the black wire from the wiring harness to

the black (hot) supply wire (Figure 4). Connect
the white wire from the wiring harness to the
white (neutral) supply wiring. Connect the green
ground wires from the hanger bracket and the
hanger ball to the supply ground wire. Use wire
connectors supplied with your ceiling fan.

23. Securely connect the wiring harness connector to

the receiver connector, and connect the blue and
yellow wires to the blue and yellow wires from the
receiver (Figure 4).

24. Turn the receiver so that the flat side aligns with

the open side of the hanger bracket (Figure 17).
Fold and position the wires into the space above
the hanger ball and into the outlet box. 

25. Feed the wires and connectors around the out-

side of the receiver, through the open side of the
hanger bracket, and into the outlet box. Slide the
receiver up and over the hanger bracket. Press
the receiver against the ceiling.

26. To complete the ceiling fan assembly, skip to the

“FINAL ASSEMBLY” section of this Owner’s
Manual.

HANGER
BRACKET

HANGER
BALL

CEILING
COVER

SW375
RECEIVER

FLAT SIDE

OPEN 
SIDE

Figure 17

8

SECTION B

Assembly Instructions for

Installing the CF2454 Ceiling Fan

with Any Other Control Method

(excluding the SW375 Receiver,

SR330 Remote Control or the

SW350 Wall Control)

1. Remove the fan motor and housing assembly from

the lower styrofoam section and position it in the lower
section so that the top of the motor is facing you.

2. Separate, untwist and unkink the four motor leads.

3. Obtain the hanger ball/downrod assembly and

remove the hanger ball by loosening the setscrew
in the hanger ball until the ball falls freely down the
downrod (Figure 18). Remove the pin from the
downrod , then remove the hanger ball. Retain the
pin and hanger ball for reinstallation in step 9.

4. Push the uplight yellow lead assembly connector

through the downrod (Figure 19) until it extends
about 4”.

5. Cut the yellow lead approximately 3” from the end

of the pipe. Strip insulation 1/2” from end of the
wires.

6. Using the wire connector supplied, connect the 

uplight yellow lead assembly to the yellow lead
from the fan motor and housing assembly.

7. Route the white, blue, and black motor leads through

the downrod. Fold the yellow wire into the slot in the
motor coupling, slide the downrod down the wires and
seat the downrod in the motor coupling (Figure 20).

8. Align the clevis pin holes in the downrod with the

holes in the motor coupling. Install the clevis pin and
secure with the hairpin clip (Figure 20). The clevis pin
must go through the holes in the motor coupling and
the holes in the downrod . Push the straight leg of the
hairpin clip through the hole near the end of the cle-
vis pin until the curved portion of the hairpin clip
snaps around the clevis pin. The hairpin clip must be
properly installed to prevent the clevis pin from work-
ing loose. Pull on the hanger ball to make sure the
clevis pin is properly installed.

HANGER BALL

DOWNROD

PIN

SETSCREW

Figure 18

4"

DOWNROD

CUT

HERE

3"

UPLIGHT YELLOW 
LEAD ASSEMBLY 

Figure 19

Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until blades are in place. Noise and fan
damage could result.

WARNING

!

Содержание ODYSSEY CF2454BQ02

















Отзывы: