background image

13

Using Your Ceiling Fan

1. Restore electrical power to the outlet box by turning

the electricity on at the main fuse box.

2. Check the operation of the fan and lights by using

the wall control or the remote control.

3. If airflow is desired in the opposite direction, turn

your fan off and wait for the blades to stop turning,
then press the rocker switch located on top of the
light kit adapter, and turn the fan on again. The fan
blades will turn in the opposite direction and
reverse airflow.

SCREW

GLASS ASSEMBLY

TOP VIEW

BOTTOM VIEW

KEYHOLE

LIGHT KIT
ADAPTER

Figure 38

Maintenance

IMPORTANT CARE INSTRUCTIONS

for your Ceiling Fan

Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.

When cleaning, use only a soft brush or lint free cloth
to avoid scratching the finish.

Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.

Trouble Shooting

TROUBLE

PROBABLE CAUSE

SUGGESTED REMEDY

1. Fan will not start.

1.Fuse or circuit breaker blown.

1. Check main and branch circuit fuses or 

circuit breakers.

2.Loose power line connections to the fan.

2. Check line wire connections to fan.

WARNING:

Make sure main power is 

turned off.

2. Fan sounds noisy.

1.Blades not attached to fan.

1. Attach blades to fan before operating.

2.Screws holding blades to flange assemblies

2. Tighten screws securely.

are loose.

3. Fan wobbles

1.Setscrew in motor coupling is loose.

1. Raise motor cover and tighten setscrew

excessively.

securely.

2.Setscrew in hanger ball/downrod assembly 

2. Tighten the setscrew in the hanger ball/

is loose.

downrod assembly.

3.Hanger bracket and/or ceiling outlet box is not

3. Tighten the hanger bracket screws to the 

securely fastened.

outlet box, and/or secure outlet box. 

4.Fan blades out of balance.

4. Interchanging an adjacent (side-by-side) 

blade pair can redistribute the weight 
and result in smoother operation. Or use 
supplied balancing kit to balance blades.

Accessories

1. Ceiling Fan Controls (see store or catalog).

2. Downrod Extension Kits (see store or catalog).

WARNING: 

FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE

TROUBLE SHOOTING YOUR FAN.

Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of an electrical shock.

WARNING

!

This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Company. Substitution of parts or acces-
sories not designated for use with this product by
Emerson Company could result in personal injury or
property damage.

WARNING

!

The use of any other control not specifically
approved for this fan could result in fire, shock and
personal injury.

WARNING

!

!

!

Содержание ODYSSEY CF2454BQ02

















Отзывы: