Emerson Liebert APM 120 Скачать руководство пользователя страница 104

Страница: 104 / 144

Operator Control and Display Panel

Liebert

APM

™

9.11.4 Screen Saver Window

If there has been no interaction with the Liebert APM’s LCD for 2 minutes, the screen saver window

appears. It remains on the LCD for 2 minutes, then the screen will go dark. The LCD will become

active again when any key is pressed.

Figure 79 Screen saver window

9.12 Pop-Up Windows

Pop-up prompt windows appear when the user must confirm a choice or perform an operation. This

section describes the pop-up windows. Some operations require entering a password; refer to

9.12.9 -

Enter Control Password

for help.

9.12.1 From Bypass to Inverter Mode With Power Interruption

If the bypass voltage or frequency exceeds the synchronized range and

utility voltage or frequency is normal, the inverter cannot be in

synchronization with the bypass, and the output can only transfer to

inverter after an interruption of about 15ms when the user presses the

INVERTER ON button. Before transferring, the system will let the

user confirm whether the interruption can be accepted, as shown at right. If the bypass voltage

returns to normal before the user makes confirmation, the UPS will transfer to inverter mode

automatically. At the same time, the prompt window will close.

9.12.2 From Inverter to Bypass Mode With Interruption

If the bypass voltage or frequency exceeds the synchronized range and

the UPS is in inverter mode, the system must let the user confirm and

accept the power interruption danger before pressing the INVERTER

OFF button to shut down the output of the inverter. The user can also

cancel the shutdown operation, as shown at right. If the bypass voltage

returns to normal before the user makes the confirmation, the UPS

will transfer to bypass operation mode automatically, and at the same time the prompt window will

disappear soon.

HELP

Single

APM 090kVA

0 2:1 7: 47

EMERSON

™

Network Power

Press any key back to main menu

Transfer with Interrupt,

please confirm or cancel

This operation leads to

output shutdown,
Confirm or cancel

Содержание Liebert APM 120

















































































































































Результаты поиска

Содержание Liebert APM 120

Отзывы:

Похожие инструкции для Liebert APM 120

Бренды по названию

Популярные бренды

Emerson Liebert APM 120, Руководство пользователя

Результаты поиска

Содержание Liebert APM 120

Отзывы:

Похожие инструкции для Liebert APM 120

Бренды по названию

Популярные бренды