Emerson Liebert APM 120 Скачать руководство пользователя страница 120 | Manualshive

Страница: 120 / 144

background image

Operation

Liebert

®

APM

™

110

10.13 Emergency Shutdown With EPO

This circuit has been designed to switch off the UPS in emergency conditions (i.e., fire, flood, etc.). The

system will turn off the rectifier, inverter and stop powering the load immediately (including the

inverter and bypass), and the battery stops charging or discharging.
If the input utility is present, the UPS’s controls will remain active; however, the output will be

turned off. To remove all power from the UPS, the external feeder breaker should be opened. (Refer to

10.14 Auto Restart

When the main and bypass sources fail, the UPS draws power from the battery system to supply the

load until the batteries are depleted. When the UPS reaches its end of discharge (EOD) threshold, it

will shut down.
The UPS will automatically restart and enable output power:

• after utility power is restored
• if “Auto Recovery after EOD Enabling” is enabled in the UPS configuration (set by factory or by

Liebert Services)

• after the “Auto Recovery after EOD Delay Time” expires (the default delay is 10 minutes)

During the auto recovery delay, the Liebert APM will be charging its batteries to provide a safety

margin for equipment shutdown if input power fails again.

If the “Auto Recovery after EOD Enabling” feature is disabled, the system must be restarted manually.

10.15 Reset After Shutdown for Emergency Stop (EPO Action) or Other Conditions

Once all appropriate measures have been taken to correct the problem indicated by the alarm

message appearing on the Operator Control Panel , carry out this procedure to restore the UPS to

regular operation following an EPO action or for the following reasons: Inverter Overtemperature,

Cut-off Overload, Battery Overvoltage, excessive switching (BYP: XFER COUNT BLOCK), etc.
When the user confirms that the fault is cleared:
1. Press the FAULT CLEAR button to let the system exit the emergency off state.
2. Press the INVERTER ON button on the right side of the Operator Control Panel for longer than

2 seconds (after the rectifier has qualified).

After the EPO button is pressed, if the input utility is removed, the UPS will shut down completely.

When input utility is restored, the EPO condition will clear, and the UPS will enable the static bypass

and restore the output.

10.16 Battery Protection

10.16.1 Battery Undervoltage Warning

Before the end of discharge, the Liebert APM displays a low battery warning. After this warning, the

battery has the capacity for 5 minutes discharging with full load (default time). The Liebert APM can

be user-configured to display this warning from 3 to 60 minutes before end-of-discharge.

10.16.2 Battery End-of-Discharge (EOD) Protection

If the battery voltage is lower than the end-of-discharge voltage, the battery converter will be shut

down.

NOTE

The rectifier will start automatically 5 minutes after the of overtemperature fault is cleared.

«
...
118
119
120
121
122
...
»

Содержание Liebert APM 120

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Liebert APM 120

Бренд: INFOSEC UPS SYSTEM Страницы: 67

Бренд: CPI Страницы: 29

Бренд: Avaya Страницы: 94

RIMATRIX5 PMC12

Бренд: Rittal Страницы: 5

GALILEO RT 1 kVA

Бренд: Borri Страницы: 56

DAKER DK Plus 3 101 70

Бренд: LEGRAND Страницы: 196

Бренд: LEGRAND Страницы: 84

Бренд: Online USV Страницы: 16

Бренд: Online USV Страницы: 19

Бренд: Xtreme Power Conversion Страницы: 86

sonnenProtect 2500-AU-ATS

Бренд: Sonnen Страницы: 27

Бренд: Lega Страницы: 28

Бренд: Salicru Страницы: 48

Бренд: Xtreme Power Conversion Страницы: 9

Бренд: Cyber Power Страницы: 72

Бренд: Eaton Страницы: 98

Galleon 1 RT 6K

Бренд: ACDC Dynamics Страницы: 35

Бренд: Xtreme Power Conversion Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды