Emerson Liebert APM 120 Скачать руководство пользователя страница 105

Страница: 105 / 144

Operator Control and Display Panel

Liebert

APM

™

9.12.3 System Self-Test

When a system self-test is completed, a pop-up window reports the

results of the test, as shown at right.

• Press the

Help

(Enter) key and the pop-up window closes.

9.12.4 Battery Capacity Test Confirmation

When a battery capacity test is started from the Command menu, the

battery will be discharged to low-battery warning level. The Liebert

APM asks for confirmation before the test is started, as shown at right.

• To confirm the choice and begin the battery capacity test, press the

Help

(Enter) key and the pop-up window disappears.

• To cancel the test, press the

(ESC) key. The pop-up window disappears.

9.12.5 Battery Self-Test Aborted, Condition Not Met

When a battery capacity test is started from the Command menu and

the battery self-test condition is inadequate, the Liebert APM will not

perform a battery test. User should check whether the battery state is

boost charging and whether the load level is greater than 20 percent.

• Press the

Help

(Enter) key and the pop-up window closes.

9.12.6 Battery Equalize Charge

The user can Enable or Disable the Battery Equalize Charge of the

batteries. Use the F3 or F4 button to Enable or Disable the Battery

Equalize feature.

• Press the

Help

(Enter) key and the pop-up window closes.

9.12.7 Battery Reset

The user can reset the battery statistics to a new battery state. Use the

F3 or F4 button to select Battery Reset

• Press the

Help

(Enter) key and the pop-up window closes.

9.12.8 Battery Refresh Charge Aborted, Condition Not Met

When a battery refreshening charge is started from the Command

menu and battery refreshening condition fails to meet requirements,

the Liebert APM will not perform a battery refreshening charge. User

should check if boost charging condition is not enough, such as (No

battery, charger failed, etc.).

• Press the

Help

(Enter) key and the pop-up window closes.

9.12.9 Enter Control Password

When a UPS control operation requires a password, the pop-up at

right will be displayed. The password is 12345.
Use the Right or Left arrow to move the cursor along the password

field. Then use the Up and Down arrows to advance until the desired

number is displayed. Enter the password one digit at a time.

NOTE

For a battery capacity test to function properly, the load must be between 20% and 100%.

System Self-Test finished.

Please check the current

warnings

Battery will be depleted,

Confirm or cancel

Battery Self-Test aborted,

Conditions not met

Battery equalize charge

enabled

Battery equalize charge

disabled

Battery reset

Battery Refresh Charge

aborted,

Conditions not met

Enter Control Password

*****

Содержание Liebert APM 120

















































































































































Результаты поиска

Содержание Liebert APM 120

Отзывы:

Похожие инструкции для Liebert APM 120

Бренды по названию

Популярные бренды

Emerson Liebert APM 120, Руководство пользователя

Результаты поиска

Содержание Liebert APM 120

Отзывы:

Похожие инструкции для Liebert APM 120

Бренды по названию

Популярные бренды