background image

www.Fisher.com

Fisher

 easy-Drive

 RPU-100

Contents

Introduction

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Scope of Manual

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Description

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Educational Services

2

. . . . . . . . . . . . . . . . . . . . . . . . .

Related Documents

2

. . . . . . . . . . . . . . . . . . . . . . . . . .

Product Operation

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Product Interfaces

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Enable / Disable Switch

3

. . . . . . . . . . . . . . . . . . . . . . .

LED Key

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

easy-Drive User Interface

5

. . . . . . . . . . . . . . . . . . . . . . .

Loss Detect

5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Status Output

5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation

6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Product Security

6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Mounting

7

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Wiring

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Replacement

15

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removal

15

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation

15

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts Ordering

15

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Appendix A - Modbus

16

. . . . . . . . . . . . . . . . . . . . . . . . .

Appendix B - Certificate of Conformance

20

. . . . . . . . .

Figure 1. Fisher easy-Drive RPU-100

X1718

Introduction

Scope of Manual

This instruction manual provides product information including installation for the Fisher easy-Drive
RPU-100. For Fisher easy-Drive actuators refer to the appropriate easy-Drive actuator instruction
manual. 

To avoid personal injury or property damage, it is important to carefully read, understand, and

follow all the contents of this manual, including all safety cautions and warnings.

 If you have any

questions about these instructions, contact your 

Emerson sales office

 before proceeding.

Description

The easy-Drive RPU-100 is a reserve power unit designed to provide backup power to the easy-Drive actuator upon
loss of incoming power. The RPU-100 provides enough power to the actuator to allow the actuator to drive the valve
to the pre-defined loss of power or loss of signal position. The RPU-100 can be ordered with a new easy-Drive assembly
or be retrofit into existing easy-Drive units that have the Gen2 control board.

Instruction Manual

D104551X012

easy-Drive RPU-100

May 2021

Содержание Fisher easy-Drive RPU-100

























Отзывы: