Emerson Fisher easy-Drive RPU-100 страница 2 Скачать руководство пользователя

Страница: 2 / 24

Instruction Manual

D104551X012

easy-Drive RPU-100

May 2021

Table 1. Specifications

Material Temperature Capabilities

-20

C (-4

F) to 70

C (158

Power Requirements

11-30 VDC, minimum 4 amp power supply required
(fuse to 5 amps)

Maximum Current Draw

4 amps

Idle Current Draw

30 mA at 24 VDC, 50 mA at 12 VDC

Hazardous Area Approvals

CSA (C/US):

ExplosionProof Class I, Division 1,

Groups C and D, T6, Ex db IIA T6, Class I, Zone 1, AEx
db IIA T6

ATEX Flameproof - Gas:

II 2 G, Ex db IIA T6 Gb

IECEx Flameproof - Gas:

Ex db IIA T6 Gb

Approximate Weight:

0.5 kg (1 lb)

Educational Services

For information on available courses for the easy-Drive RPU-100, as well as a variety of other products, contact:

Emerson Automation Solutions
Educational Services - Registration
Phone: 1-641-754-3771 or 1-800-338-8158
E-mail: [email protected]
emerson.com/fishervalvetraining

Содержание Fisher easy-Drive RPU-100

























Результаты поиска

Содержание Fisher easy-Drive RPU-100

Отзывы:

Похожие инструкции для Fisher easy-Drive RPU-100

Бренды по названию

Популярные бренды

Emerson Fisher easy-Drive RPU-100, Инструкция по эксплуатации

Результаты поиска

Содержание Fisher easy-Drive RPU-100

Отзывы:

Похожие инструкции для Fisher easy-Drive RPU-100

Бренды по названию

Популярные бренды