background image

 

1592031000 Univ-R4 GB - r1.1 - 2012.07.23                         Universal-R 

                                                                   4/20 

 

2.

 

GENERAL WARNING 

WARNING: The Universal-R should always be installed by a suitable qualified person, in accordance with best 
electrical  and  refrigeration  practice.  Take  time  to  read  the  instructions.  Do  not  exceed  the  relay  ratings.  The 
Universal-R should not be considered a safety device, use suitable safety cutout devices when appropriate. 

 

This manual is part of the product and should be kept near the instrument for easy and quick reference. 

 

The instrument shall not be used for purposes different from those described hereunder. It cannot be used as a safety device. 

 

Check the application limits before proceeding. 

 

Dixell  Srl  reserves  the  right  to  change  the  composition  of  its  products,  even  without  notice,  ensuring  the  same  and  unchanged 
functionality. 

2.1

 

SAFETY PRECAUTIONS  

 

Check the supply voltage is correct before connecting the instrument. 

 

Do not expose to water or moisture: use the controller only within the operating limits avoiding sudden temperature changes with high 
atmospheric humidity to prevent  formation of condensation 

 

Warning: Disconnect all electrical connections before any kind of maintenance. 

 

The instrument must not be opened. 

 

Fit the probes where they are not accessible by the End User. 

 

In case of failure or faulty operation send the instrument back to the distributor with a detailed description of the fault. 

 

Do not exceed the maximum current that can be applied to each relay (see Technical Data). 

 

Ensure  that  the  wires  for  probes,  electrical  loads  and  the power supply are separated and far enough away to each other, without 
crossing or intertwining. 

 

In case of applications in industrial environments, the use of mains filters (our mod. DIXL930) in parallel with inductive loads could be 
useful. 

 

Heating applications – Do not exceed 105°C with the NTC probes supplied. For higher temperatures (up to a maximum of 150°C) 
use special PTC probes (e.g. our Part No. DIXL957). 

3.

 

GENERAL DESCRIPTION 

Model Universal-R is a 71x29 mm format microprocessor based controller, suitable for applications on high, medium or low temperature 
refrigeration  units.  It  is  provided  with  three  relay  outputs  to  control  compressor,  defrost  -  which  can  be  both  electrical  or  hot  gas  -  and 
evaporator fans. It can work with PTC or NTC probes. Where defrost is being terminated by time, it can operate with just one thermostat 
probe. Where defrost is being terminated by temperature, it has an input for an evaporator probe(s). 
 
The Universal-R is equipped with an internal alarm buzzer, a flashing visual alarm as well as a 4th relay (volt free) that can be configured 
as  Auxiliary  or  Alarm, to control a heater in Dead Band control (see parameter oAC) or to control the defrosting of a second evaporator 
(when “tC” parameter is set to 6). 
 
Double  evaporator  defrost:  When  tC=6,  the  controller  is  set  up  to  defrost  twin  evaporators.  Defrost  of  both  evaporators  will  start 
simultaneously but each evaporator will terminate defrost individually on temperature. Only when both evaporators have terminated defrost, 
will the controller revert to refrigeration. 
   
Each instrument is fully configurable through special parameters that can be easily programmed through the keypad. 
 

Содержание Dixell Universal-R





















Отзывы: