Emerson COPELAND ZH04K1P Скачать руководство пользователя | Manualshive

Страница: 23 / 39

background image

20

AGL_HP_ST_ZHK1P_EN_Rev00

Figure 20: Maximum thickness of cable shoe connectors

Cable  glands  have  an  inf luence  on  the  protection  class  of   the  terminal  box.  It  is  strongly
recommended  to  use  appropriate  cable  glands  in  order  to  reach  the  rated protection class.
Emerson advises installers/service providers to pay attention to this aspect every time they inst all
or replace a Copeland scroll compressor and to use cable glands according to E N 50262 o r any
other  relevant  standard  of   application  in  their  country/region.  Examples  of   c orrect electrical
installations are shown in

Figures 21 & 22

below.

Figure 21: Correct electrical installation with cable glands for IP21 T-box, eg, model ZH04K1P

Figure 22: Correct electrical installation with cable glands for IP54 T-box (model ZHI46K1P)

«
...
21
22
23
24
25
...
»

Содержание COPELAND ZH04K1P








































Отзывы:

Нет отзывов

Похожие инструкции для COPELAND ZH04K1P

Бренд: Daikin Страницы: 51

Бренд: Fubag Страницы: 19

Бренд: Arnott Страницы: 7

Performer S Series

Бренд: Danfoss Страницы: 28

Maneurop LTZ-R404A

Бренд: Danfoss Страницы: 24

Maneurop NTZ Series

Бренд: Danfoss Страницы: 34

ROPULS eDM Series

Бренд: Rothenberger Страницы: 120

Бренд: Daikin Страницы: 32

POWERplus POWX1760

Бренд: VARO Страницы: 10

Бренд: Ingersoll-Rand Страницы: 101

Бренд: Central Pneumatic Страницы: 2

Бренд: SHARKS Страницы: 31

JEFC100L10B-230

Бренд: Jefferson Professional Tools & Equipment Страницы: 13

JEFC050L10B-230

Бренд: Jefferson Страницы: 20

X-ONE 511010614

Бренд: Matrix Страницы: 12

Бренд: Airworks Страницы: 36

Airwave RA-C2550-G

Бренд: Ryobi Страницы: 19

Бренд: VPK Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды