Emerson Copeland Eazycool OLTE-82D-TFD Скачать руководство пользователя страница 50

Страница: 50 / 55

C6.1.9/0219/E

Code

Description

Cause

Action

Reset

E55

Fan failure

Fan alarm contact open Warning signal only

Check fans protection

E60

Max pressure alarm of superheating

When the temperature
which converts from
suction pressure rises
above the set threshold
(MoP/L08) for the time
dMP/L10

The MOP control ends when the superheat is
lower than the superheating setpoint

E61

Min pressure alarm of superheating

When the temperature
which converts from
suction pressure falls
below the set threshold
(LoP/L09) for the time
dLP/L11

The LOP control ends when the temperature
rises to 4°C above the threshold of LoP/L09 or
in case of superheating under the SET low
superheat when the temperature is in [LOP,
LOP+4°C]

E62

High superheating alarm

If the superheat
remains above
HSH/L04 for HSd/L06

Valve is opened at (HSt/M01).

Automatically with the SH condition

E63

Low superheating alarm

If superheat below
LSH/L03

Valve will slowly close to the LSt/M02

Automatically with the SH condition

E64

High room temperature alarm

If temperature above
ALU/G48

Warning signal only

If temperature

≤ ALU/G48-AHY/G50 reset

E65

Low room temperature alarm

If temperature below
ALL/G49

Warning signal only

If temperature

≥ ALL/G49+AHY/G50

E66

Door open alarm

If the door is open
longer than dSA/G53

Warning signal only if rrd/G09 is "no"
Alarm and compressor trip if rrd/G09 is
"yes"

Manual or automatic

– see Action

E80

rtC warning, date not correct

HW problem in the
board

Disable the rtC or change the board

E81

rtC warning, communication error

HW problem in the
board

Disable the rtC or change the board

Содержание Copeland Eazycool OLTE-82D-TFD
























































Результаты поиска

Содержание Copeland Eazycool OLTE-82D-TFD

Отзывы:

Бренды по названию

Популярные бренды

Emerson Copeland Eazycool OLTE-82D-TFD, Инструкции по применению

Результаты поиска

Содержание Copeland Eazycool OLTE-82D-TFD

Отзывы:

Бренды по названию

Популярные бренды