Emerson Control Techniques EN Series Скачать руководство пользователя | Manualshive

Страница: 30 / 264

background image

11

Operational Overview

Pulse Mode Parameters

The

Pulse Position

Input

parameter shows the total pulse count received by the drive since

the last power-up.

The

Pulse Position Input

,

Position Command

,

Position Feedback Encoder

and

Position

Feedback

are initialized to zero on power-up. Only

Position Feedback Encoder

can be pre-

loaded serially with a value after power-up.

The

Pulse Mode Ratio

parameter includes a numerator which represents motor revolutions,

and a denominator which represents master pulses. The Pulse Ratio Revolutions is allowed
to be negative which reverses all Pulse mode motion.

The

Pulse Position Input

is multiplied by the Pulse Mode Ratio to produce the

Position

Command

.

Following Error/Following Error Limit

The Following Error is the algebraic difference between the Position Command and the
Position Feedback. It is positive when the Position Command is greater than the Position
Feedback. All accumulated Following Error will be cleared when the drive is disabled.

The Following Error Limit is functional in Pulse mode only. A Following Error Limit can be
set using PowerTools FM or a FM-P. This limit is in motor revolutions and has a range of
.001 to 10.000 revolutions. The Following Error Limit can be enabled or disabled.

Pulse Mode Following Error

In Pulse Mode, the range of the Following Error is ±2863.3 revolutions. If the Following
Error Limit is not enabled and the Following Error exceeds 2863.3 revolutions, the displayed

value is limited to this maximum value and will not rollover.

If the Following Error Limit Enable is enabled, the absolute value of the Following Error will
be compared to the Following Error Limit. If the limit is exceeded, a fault will be generated.

If the Following Error Limit Enable is disabled, the Following Error Limit is not used.

Velocity Mode Following Error

In Velocity mode, the maximum Following Error possible varies based on the gain and torque

limit settings. When the Actual Torque Command reaches the maximum possible level, the
following error will stop increasing and any additional position error will be dropped. In
Velocity mode, when the following error exceeds the Following Error Limit parameter there

is no action.

Encoder Feedback and Position Feedback

Encoder Feedback (Position Feedback Encoder) and Position Feedback are two separate

parameters which indicate the same physical motor position. Encoder Feedback is the
position change since power up in motor encoder counts and Position Feedback is the total
position change since power up in motor revolutions. The Position Direction parameter

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
28
29
30
31
32
...
»

Содержание Control Techniques EN Series









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Control Techniques EN Series

Бренд: IBM Страницы: 76

Бренд: Fastech Страницы: 26

Бренд: D+H Страницы: 2

Бренд: RIB Страницы: 44

EUP200AD-1H12V-0

Бренд: EUCHIPS Страницы: 4

Бренд: Grundfos Страницы: 24

Бренд: Applied Motion Products Страницы: 44

Бренд: Lin Engineering Страницы: 29

Allen Bradley Kinetix 7000 2099-BM06-S

Бренд: Rockwell Automation Страницы: 38

Бренд: EACON Страницы: 18

Бренд: IBM Страницы: 20

MECHATROLINK-II

Бренд: YASKAWA Страницы: 46

Бренд: YASKAWA Страницы: 267

VLT 2800 Series

Бренд: Danfoss Страницы: 103

Бренд: SAJ Страницы: 30

Бренд: ABB Страницы: 52

MECHATROLINK-III

Бренд: YASKAWA Страницы: 41

Sigma-II Series

Бренд: YASKAWA Страницы: 578

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды