Emerson 8700 Series Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 136

background image

Reference Manual

00809-0100-4793, Rev CA

August 2004

Rosemount 8742C

4-10

FAILED_MASK

This parameter will mask any of the failed conditions listed in
FAILED_ENABLED. A bit on means that the condition is masked out from
alarming and will not be reported.

FAILED_PRI

Designates the alarming priority of the FAILED_ALM. The default is 0 and
the recommended value are between 8 and 15.

FAILED_ACTIVE

This parameter displays which of the alarms is active. Only the alarm with
the highest priority will be displayed. This priority is not the same as the
FAILED_PRI parameter described above. This priority is hard coded within
the device and is not user configurable.

FAILED_ALM

Alarm indicating a failure within a device which makes the device
non-operational.

MAINT_ALARMS

A maintenance alarm indicates the device or some part of the device needs
maintenance soon. If the condition is ignored, the device will eventually fail.
There are five parameters associated with MAINT_ALARMS, they are
described below.

MAINT_ENABLED

The MAINT_ENABLED parameter contains a list of conditions indicating
the device or some part of the device needs maintenance soon. If the
condition is ignored, the device will eventually fail.

Below is a list of the conditions with the highest priority first.

1.

Auto Zero Failure

2.

NV Writes Deferred

3.

Reverse Flow Detected

4.

Electronics Trim Failure

5.

Empty Pipe

6.

PWA Simulate Active

7.

PV Range Exceeded

MAINT_MASK

The MAINT_MASK

parameter will mask any of the failed conditions listed

in MAINT_ENABLED. A bit on means that the condition is masked out
from alarming and will not be reported.

MAINT_PRI

MAINT_PRI

designates the alarming priority of the MAINT_ALM. The

default is 0 and the recommended values is 3 to 7.

MAINT_ACTIVE

The MAINT_ACTIVE

parameter displays which of the alarms is active.

Only the condition with the highest priority will be displayed. This priority is
not the same as the MAINT_PRI parameter described above. This priority
is hard coded within the device and is not user configurable.

«
...
47
48
49
50
51
...
»

Содержание 8700 Series









































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8700 Series

Бренд: DAVIS Страницы: 12

Ultraprobe 9000

Бренд: UE Systems Страницы: 25

ULTRAPROBE 10000

Бренд: UE Systems Страницы: 6

Бренд: Kobold Страницы: 55

Бренд: Hilti Страницы: 146

Бренд: Datakom Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Banner Страницы: 4

Бренд: Hanna Instruments Страницы: 21

WATERPROOF PHTESTR 1 PH TESTER

Бренд: EUTECH INSTRUMENTS Страницы: 3

AirScout Gigacheck

Бренд: Greenlee Страницы: 19

Бренд: Keysight Technologies Страницы: 45

Бренд: Omega Страницы: 12

Бренд: Digitimer Страницы: 58

Бренд: Metrohm Страницы: 163

Field Check PLUS

Бренд: Martin Lishman Страницы: 7

Бренд: PCE Health and Fitness Страницы: 7

Бренд: ICP DAS USA Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды