Emerson 8700 Series Скачать руководство пользователя страница 126

Страница: 126 / 136

Reference Manual

00809-0100-4793, Rev CA

August 2004

Rosemount 8742C

D-4

TRANSDUCER BLOCK
ERRORS

The following conditions are reported in the BLOCK_ERR and XD_ERROR
parameters. Conditions in

italics

are inactive for the transducer block and are

given here only for your reference.

Table D-4. Transducer
BLOCK_ERR and XD_ERR
Conditions

Condition

Number

Condition Name and Description

Block Configuration Error

Link Configuration Error

Simulate Active

Local Override

Device Fault State Set

Device Needs Maintenance Soon

Input Failure/Process Variable Has Bad Status

Output Failure

Memory Failure

Lost Static Data

Lost NV Data

Readback Check Failed

Device Needs Maintenance Now

Power Up

The device was just powered-up.

Out of Service

: The actual mode is out of service.

Unspecified Error

: An unidentified error occurred.

General Error

: A general error that cannot be specified below occurred.

Calibration Error

: An error occurred during calibration of the device, or

a calibration error was detected during normal operations.

Configuration Error

: An error occurred during configuration of the

device, or a configuration error was detected during normal operations.

Electronics Failure

: An electrical component failed.

Mechanical Failure

: A mechanical component failed.

I/O Failure

: An input/output (I/O) failure occurred.

Data Integrity Error

: Data stored in the device are no longer valid due

to a nonvolatile memory checksum failure, a data verify after write
failure, etc.

Software Error

: The software has detected an error due to an improper

interrupt service routine, an arithmetic overflow, a watchdog time-out,
etc.

Algorithm Error

The algorithm used in the transducer block produced

an error due to overflow, data reasonableness failure, etc.

Содержание 8700 Series









































































































































Результаты поиска

Содержание 8700 Series

Отзывы:

Похожие инструкции для 8700 Series

Бренды по названию

Популярные бренды

Emerson 8700 Series, Справочное руководство

Результаты поиска

Содержание 8700 Series

Отзывы:

Похожие инструкции для 8700 Series

Бренды по названию

Популярные бренды