Emerson 8700 Series Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 136

background image

Reference Manual

00809-X0100-4793, Rev CA
August 2004

4-3

Rosemount 8742C

AI BLOCK

The Analog Input (AI) function block provides the primary interface of the
measurement to the control and/or monitoring systems. To properly configure
the device, three parameters must be set in order to correctly interface
between the AI block and transducer block.

1.

The CHANNEL parameter defines which transducer block
measurement is used by the AI block. In the 8742C Magnetic
Flowmeter Transmitter, only one channel is available: AI1.CHANNEL
= 1 (Flow).

2.

The second parameter is the XD_SCALE.UNITS_INDX. The default
configuration is feet per second (ft/s). Other units are available and
listed in Appendix D: Table D-3.

3.

Finally, since the flow measurement from the transducer block is in
the correct units, L_TYPE is configured as Direct. L_TYPE can be
either Direct or Indirect.

NOTE

Refer to the F

OUNDATION

fieldbus Block product manual, document

00809-0100-4783, for more details on configuring and troubleshooting the AI
Block.

ARITHMETIC BLOCK

The Arithmetic function block provides the ability to configure a range
extension function for a primary input and applies the nine (9) different
arithmetic types as compensation to or augmentation of the range extended
input. All operations are selected by parameter and input connection.

The nine (9) arithmetic functions are Flow Compensation Linear, Flow
Compensation Square Root, Flow Compensation Approximate, Btu Flow,
Traditional Multiply and Divide, Average, Summer, Fourth Order Polynomial,
and Simple HTG Compensate Level.

This Arithmetic function block supports mode control (Auto, Manual, and Out
of service). There is no standard alarm detection in this block.

NOTE

Refer to the F

OUNDATION

fieldbus Block product manual, document

00809-0100-4783, for more details on configuring and troubleshooting the
Arithmetic Block.

INTEGRATOR

The Integrator (INT) function block integrates one or two variables over time.
The block compares the integrated or accumulated value to pre-trip and trip
limits and generates discrete output signals when the limits are reached.

The Integrator function block supports mode control, demand reset, a reset
counter, and signal status calculation. There is no process alarm detection in
the block.

NOTE

Refer to the F

OUNDATION

fieldbus Block product manual, document

00809-0100-4783, for more details on configuring and troubleshooting the
Integrator Block.

«
...
40
41
42
43
44
...
»

Содержание 8700 Series









































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8700 Series

Бренд: Candela Страницы: 4

Бренд: VEE GEE Страницы: 2

Бренд: QMI Страницы: 54

Бренд: S.E. International Страницы: 30

Бренд: SZBJ Страницы: 2

Бренд: Ansul Страницы: 24

Бренд: ENDA Страницы: 2

Бренд: Heinrichs Страницы: 31

Бренд: FISCHER Страницы: 20

Бренд: Jaquet Страницы: 27

Бренд: LaserLiner Страницы: 52

Бренд: PASCO Страницы: 13

Simple Precision OWD

Бренд: KAM Страницы: 41

Бренд: Z-Wave Страницы: 5

Бренд: Klein Tools Страницы: 20

Бренд: Extech Instruments Страницы: 8

Бренд: TESTO Страницы: 2

Telecaster Bass

Бренд: Fender Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды