Emcotec RC Electronic DPSI LCD Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 32

background image

DPSI LCD Operating Instructions

Version 1.0

Page 28 of 32

9.5. Units

Programming of units is conducted identical to all other settings. When
programming switching positions, the units are always specified in %.
In this case this setting therefore refers only to the display of the servo
positions during normal operation.

9.6. Battery Type

In order to guarantee correct low voltage indication (depending on the
base system), the battery type must be programmed. Because different
batteries have different voltages, this programming is mandatory.

«
...
26
27
28
29
30
...
»

Содержание RC Electronic DPSI LCD

































Отзывы:

Нет отзывов

Похожие инструкции для RC Electronic DPSI LCD

Smart-MPPT Li Series

Бренд: Y-Solar Страницы: 6

Бренд: Accel Страницы: 8

Бренд: GBD Страницы: 68

Бренд: Lattice Semiconductor Страницы: 2

Бренд: Lathem Страницы: 4

Бренд: tams elektronik Страницы: 36

Gemini GEM-P9600

Бренд: NAPCO Страницы: 6

Gemini GEM-P816

Бренд: NAPCO Страницы: 56

Бренд: TWR Lighting Страницы: 49

Бренд: Anilam Страницы: 31

Бренд: Rinnai Страницы: 7

Бренд: Telit Wireless Solutions Страницы: 45

Бренд: YOKOGAWA Страницы: 33

Бренд: Velux Страницы: 11

Бренд: Kantronics Страницы: 201

Бренд: Lika Страницы: 28

Бренд: Vega Страницы: 28

Бренд: WATSON Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды