background image

49

IND100241-21

Appendix

Pinout Assignments

Connectors illustrated here are either standard by factory default or may be available (through factory customization).

Note that some combinations may not be possible due to space restrictions. List also valid for customized models. All 

pin out assignments are seen from users Point of View (POV) while looking straight at the connector. Please review 

the dedicated datasheet or technical drawings for your actual unit to identify and determine the presence of desired 

connector. Detailed information about Housing Connectors (terminal blocks) can be found earlier in this manual.

18/24/24+5 pin DVI-D, DVI-I, Single Link, Dual Link Combined Female

1  2  3  4  5  6  7  8     C1 C2

 9 10 11 12 13 14 15 16      C5

17 18 19 20 21 22 23 24  C3  C4 

PIN 01 T.M.D.S. Data2 - (Digital - RED link 1)

PIN 02 T.M.D.S. Data2 + (D RED link 1)

PIN 03

T.M.D.S. Data2/4 Shield

PIN 04 T.M.D.S. Data4 - (Digital - GREEN link 2)

PIN 05

T.M.D.S. Data4 + (D GREEN link 2)

PIN 06 DDC Clock

PIN 07 DDC Data

PIN 08 Analog Vertical Sync (DVI-I only)

PIN 09 T.M.D.S. Data1 - (Digital - GREEN link 1)

PIN 10 T.M.D.S. Data1 + (D GREEN link 1)

PIN 11 T.M.D.S. Data1/3 Shield

PIN 12 T.M.D.S. Data3 - (Digital - BLUE link 2)

PIN 13 T.M.D.S. Data3 + (D BLUE link 2)

PIN 14

+5V Power (for standby mode)

PIN 15 Ground (for +5V and analog sync)

PIN 16 Hot Plug Detect

PIN 17 T.M.D.S. Data0 -  (Digital - BLUE link 1) and digital sync.

PIN 18 T.M.D.S. Data0 + (D BLUE link 1) and digital sync.

PIN 19 T.M.D.S. Data0/5 Shield

PIN 20 T.M.D.S. Data5 - (Digital - RED link 2)

PIN 21 T.M.D.S. Data5 + (Digital - RED link 2)

PIN 22 T.M.D.S. Clock Shield

PIN 23 T.M.D.S. Clock + (Digital clock + (Links 1 and 2)

PIN 24

T.M.D.S. Clock - (Digital clock - (Links 1 and 2)

PIN C1 Analog RED

PIN C2 Analog GREEN

PIN C3 Analog BLUE

PIN C4

Analog Horizontal Sync.

PIN C5 Analog Ground (return for RGB signals)

DDC = Display Data Channel. 

T.M.D.S = Transition Minimized Differential Signal

PIN C1,C2,C3,C4 = Only present on DVI-I connectors.

NOTE: Connector shows a DUAL LINK design, but some units may not support it. 

Only units with 1920x1200 or more in resolution require / support DUAL LINK.

Analog RGB/VGA, 15-pin DSUB High Density Female

Onboard or via DVI-4 adapter

5  4  3  2  1

15   14   13   12   11

10  9  8  7  6

PIN 01 RED

Red, analog

PIN 02 GREEN

Green, analog

PIN 03 BLUE

Blue, analog

PIN 04

ID2/RES

Reserved for monitor ID bit 2 (grounded)

PIN 05 GND

Digital ground

PIN 06 RED_RTN

Analog ground red

PIN 07 GREEN_RTN Analog ground green

PIN 08 BLUE_RTN

Analog ground blue

PIN 09 KEY/PWR

+5V power supply for DDC (optional)

PIN 10 GND

Digital ground

PIN 11 ID0/RES

Reserved for monitor ID bit 0 (grounded)

PIN 12 ID1/SDA

DDC serial data

PIN 13 HSYNC.

Horizontal sync or composite sync, input

PIN 14

VSYNC.

Vertical sync, input

PIN 15 ID3/SCL

DDC serial clock

8-pin RJ45 10/100/1000Mbps LAN/Ethernet

1  2  3  4  5  6  7  8

PIN 01 D0P+ Differential Pair 0 (Positive)

PIN 02 D0N- Differential Pair 0 (Negative)

PIN 03 D1P+ Differential Pair 1 (Positive)

PIN 04

D2P+ Differential Pair 2 (Positive)

PIN 05 D2N- Differential Pair 2 (Negative)

PIN 06 D1N- Differential Pair 1 (Negative)

PIN 07 D3P+ Differential Pair 3 (Positive)

PIN 08 D3N- Differential Pair 3 (Negative)

Serial COM RS-232 non-isolated, 9-pin DSUB Male

1   2   3   4   5 

6   7    8   9

PIN 01 DCD

Data Carrier Detect

PIN 02 RxD

Receive Data

PIN 03 TxD

Transmit Data

PIN 04

DTR

Data Terminal Ready

PIN 05 GND

Signal Ground

PIN 06 DSR

Data Set Ready

PIN 07 RTS

Request To Send

PIN 08 CTS

Clear To Send

PIN 09 RI

Ring Indicator

4-pin USB TYPE A

Pin 2: Negative Data

Pin 1: VCC +5V

Pin 3: Positive Data

Pin 4: Ground

Содержание Hatteland Display HT B22G Series





































































Отзывы: