background image

26

IND100129-168

Specifications - HT B22Gx STC-yzz-Mzzz

SPECIFICATIONS

Note: All specifi cations are subject to change without prior notice!

Please visit www.hatteland-display.com for the latest electronic version.

2/2

T E C H N I C A L   D E S C R I P T I O N

• W:220.00 [8.66"] x H:89.85 [3.54"] x D:300.00 [11.81"] mm [inch]

• Weight: 5.3kg / 11.7lbs

• Aluminium Cooling Chassis

• Power Button, Reset Button, Power LED, Activity LED HDD/SSD on trays

Multi-power Supply:

• 115&230VAC - 50/60Hz + 24VDC 

: 1 x STD IEC + 1 x 2-pin Terminal Block 5.08

   

 

 

 

Note: You may connect either AC power or DC power or both. In case both sources are connected, power will be

   

 

 

 

sourced from the AC input. If AC input is lost, there will be a uninterrupted switch-over to DC input.

• Power Consumption - Operating 

: 42W (typ)* - 60W (max) - *at 25% load

• Operating 

: Temperature -15 deg. C to +55 deg. C  

   

 

  Humidity up to 95%

• Storage  

: Temperature -30 deg. C to +70 deg. C

   

 

  Humidity up to 95%

Compass Safe Distance: Standard: 135cm - Steering: 85cm

• Operating System : None or see table below

• Processor 

: 1 x Intel® Core™ i5-520E (2.40GHz, Front Side Bus: Dual Core 800/1066MHz, 3MB Cache) or see table below

• Memory/RAM 

: 1 x 2GB Single Channel, 200-pin 1 slot ECC DDR3 800/1066MHz or see table below 

• Storage 

: 2 x 2.5" removable (HDD/SSD) in front tray, see table below for sizes

• Graphics 

: Intel® Arrandale IGD, DVMT 5.0, OpenGL 2.1, DirectX 10.0, OpenCL (not supported)    

1 x DVI-I + 1 x HD DB15F

• Graphics Res. 

: VGA 2048 x 1536 @ 75 Hz; DVI-I 1920 x 1200 @ 60 Hz - HW Decoder: Intel CVT HD

• System Chipset  : Intel® BD82QM57

• BIOS 

: UEFI AMIBIOS

• PCI Slots 

: None

• Ethernet #1 

: 1 x 10/100/1000Mbps, Intel® 82577LM Gigabit LAN 

 

 

 

 

1 x RJ-45

• Ethernet #2 

: 1 x 10/100/1000Mbps, Realtek RTL8111C Gigabit LAN 

 

 

 

 

1 x RJ-45                     

• Serial Port COM1  : 1 x RS-232 - Baud Rate Min: 50b/s, Max: 115200b/s (120Kb/s), Non-isolated port 

 

1 x DB9M

• Serial Port COM2  : 1 x RS-422/RS-485 - Baud Rate Min: 50b/s, Max: 1497600b/s (1.5Mb/s), Non-isolated port 

1 x DB9M

• Serial Port COMx  : 4 x RS-422/RS-485 NMEA isolated 4 channel module) (PCA100293-1)  

 

 

4 x 5-pin Terminal Block 3.81

• USB Ports #1  

: 2 x USB2.0 (<5m)   

 

 

 

 

 

 

 

2 x USB Type A in front

• USB Ports #2  

: 3 x USB2.0 (<5m)  

 

 

 

 

 

 

 

3 x USB Type A in rear

• USB Ports #3 

: 1 x USB1.1 (<10m) 

 

 

 

 

 

 

 

1 x USB Type A in rear

• Keyboard Port 

: Standard PS/2 mini DIN connector 

 

 

 

 

 

 

1 x PS/2

• Mouse Port  

: Standard PS/2 mini DIN connector 

 

 

 

 

 

 

1 x PS/2

• Audio  

: Realtek ALC892 supports 5.1 channel, Line-Out, Mic-in or +option HT 00271 OPT-A1 

 

2 x 3.5mm mini jack (or +1 x DB9F)

• Speaker 

: No

• Power Manager  : ACPI S3/S4

• Watchdog Timer  : 256 Segments, 0, 1, 2...255 sec/min

• H/W Status Mont. : Temperatures, voltages & cooling fan status. Auto throttling control if CPU overheats

 T E C H N I C A L   D E S C R I P T I O N

Power Specifications:

Physical Specifications:

Environmental Considerations:

Lifetime Considerations:

Even although the test conditions for bridge units provide for a maximum

operating temperature of 55°C, continuous operation of all electronic

components should, if possible, take place at ambient temperatures of only

25°C. This is a necessary prerequisite for long life and low service costs.

M E C H A N I C A L   D E S C R I P T I O N

External Connector Type:

• 1 x PCA100293-1 (4 x COM RS-422/485 isolated NMEA 4 channel)

• 1 x ZIA0001310-B (1 x CAN isolated, 2 channel)

• 1 x PCA100297-1 (4 x Digital Input/Output isolated) 

• 1 x HT 00271 OPT-A1 (2W Amplified Audio out via DB9F)

• 1 x HT 00272 OPT-A1 (Parallel Port LPT, DB25F, Bi-Dir. ECP/EPP)

• 1 x PCA100298-1 (LAN 10/100Mbps, 2 ports (RJ45)

• 1 or 2 x PCA100309-1: Dual Isolated RS-232, 2xDB9 module

• Variations of SSD/HDD Storage, RAM Memory and Operating System

* Contact us for possible combinations. Review separate datasheet for more info.

Factory Mounted Options:

Type

Description

Size/Speci

 cation

CPU

1 x Intel® Core™ i5-520E (standard factory default)

or 1 x Intel® Core™ i7-620LE

or 1 x Intel® Celeron® P4505

- Dual Core 2.40GHz, Front Side Bus: 800/1066MHz, 3MB Cache

- Dual Core 2.0GHz, Front Side Bus: 1066Mhz, 4MB Cache

- Dual Core 1.86GHz, Front Side Bus: 800Mhz, 2MB Cache

Memory 1 x Single Channel, 200-pin 1 slot ECC DDR3 800/1066MHz SO-DIMM - 2GB (Standard), 4GB (Max)
Storage 2 x 2.5" SSD SATA Multi Level (MLC)

- 150GB (412TBW),240GB (599TBW),480GB (945TBW),960GB (1750TBW)

Storage 2 x 2.5" HDD SATA

- 1TB

Storage 2 x 2.5'' HDD SATA Ruggedized/Automotive

- 320GB

OS 

Option

Embedded Enterprise (WEE): Microsoft® Windows® Server 2003/2008/2008R2 (Eng), Microsoft® Windows® 2003/2008/2008R2 (Eng),

Microsoft® Windows® 7 Professional/Ultimate (Eng, SP1), Windows® 10 IoT Enterprise 2016 LTSB (64bit).

Linux: openSUSE® 11.4, Fedora™ 15, Ubuntu® 10.04 LTS, Ubuntu® 12.04 LTS. See also Accessories (HT 00300 MSOS) options.

Notes

Review "SSD Selection Guide" in manual. 32bit or 64bit versions available where applicable.

Available Computer Configurations:

Computer Specifications: (Standard model)

• HT 00270 OPT-A1: 1 x Mounting Bracket Kit - included with delivery

• HT 00262 OPT-A1: 4 x RS-422/RS-485 isolated, USB ext. module

• HT 00263 OPT-A1: 4 x RS-232 COM non-isolated, USB ext. module

• HT 00264 OPT-A1: 1 x CAN isolated, 2 channel, USB ext. module

• HT 00273 OPT-A1: 4 x Digital IN/OUT isolated, USB ext. module

• HT 00274 OPT-A1: 2 x LAN 10/100Mbps, RJ45, USB ext. module

• HT 00228 OPT-A1: 1 x Mounting Plate with cable relief, RAL 9011

• JH C01MF A-A: 1 x USB Cable 1m, Type A to Chassis mount receptacle

• HD 000TR SX1-A1: 1 x Removable Front Tray 2.5" Empty

• HD xxxyy SX1-z1: 1 x Removable Front Tray 2.5" w/Storage Device*

• HT 00300 MSOS: OS options ->

 http://www.hatteland-display.com/os

Available Accessories:

These products have been tested / type approved by the following classification societies:

IEC 60945 4th (EN 60945:2002) 

 

IACS E10  

 

 

EN55024 

 

EN55022, Class A

MIL-STD-810F 

 

 

 

EU RO MR - Mutual Recognition (covers DNV, BV, ABS, GL, NK and LRS certificates)

A P P R O V A L S    &   C E R T I F I C A T E S

Shock test 30g 11ms - Shock test 50g 11ms + Storage tests (24hours) Passed.

Additional Testing (MIL-STD-810F):

*Where xxx=Size of device. yy=GB,TB. z=S (SSD), z=H (HDD) - Choose Storage Device from table above.

Содержание Hatteland Display HT B22G Series





































































Отзывы: