Embassy ONEX Скачать руководство пользователя

Страница: 60 / 80

Figure 45 - Mounting and removing the casing on models
45WE and 45AE

13.3 - Removing the
plastic cover on a
45WE and 45AE
boilers

In order to remove the casing, follow
the steps below while refering to figure
45:

remove screw “E”;

push upward, with your hands, in
the points indicated by “Q” and “R”;

pull-out all the cover

press the two plastic springs, item
“L”, down;

lower the electrical box “S”;

lift latch “G”;

pull the bottom of cover “H” out by
around 4 in (10 cm);

lift cover “H” up by around 1in (2 cm)
and remove it.

13.3.1 - Installing
the plastic cover on
models 45WE and
45AE boilers

Boilers models 45AE and 45WE are
delivered with the plastic outer jacket
cover in a separate box and need to be
field installed. In order to install the
plastic cover, follow the steps below
while refering to figure 45:

mount the boiler as per section 5.5;

mount the coaxial adaptor item “B”
in figure 45 bis, as per section 10.1;

plumb the plastic cover “B” onto the
boiler;

with both hands, push on points “C”
and “D” at the same time;

secure cover “B” with screw “E” and
washer “F”;

insert washer “A” onto the coaxial
adaptor.

Figure 45 bis - Mounting the plastic cover on a 45WE or
45AE

Содержание ONEX

















































































Результаты поиска

Содержание ONEX

Отзывы:

Похожие инструкции для ONEX

Бренды по названию

Популярные бренды

Embassy ONEX, Инструкция по установке и обслуживанию

Результаты поиска

Содержание ONEX

Отзывы:

Похожие инструкции для ONEX

Бренды по названию

Популярные бренды