Embassy ONEX Скачать руководство пользователя

Страница: 54 / 80

12 - USE

“L”

Code

Lock-out

description

Controls

Solutions

L18

L19

L20

L25

L32

L33

L45

L46

Program error

Flame sensed for 10
seconds, after the closure
of the gas valve

Flame sensed before
opening of the gas valve.

U1 or U6 sensor increase
its temperature too fast

Program error

Fan rotation error

Heating circuit filling time
longer than 10 minutes.

Check:
a - that the heating water flow is not

too low;

b - that the circulator pump is working

Check that the voltage to the fan is
163(

10)Vdc.

Replace the power control board

Replace the gas valve, or replace the power control board

a - If temperature difference between U1 and U8 is higher

than 55

F (13

C), at maximum input, the heating water flow

rate is too low. The heating water flow rate must be
corrected.

b - replace the circulator pump or the power control board.

Check:
a - that the heating pressure switch

setting pressure, FILL must appear
when the pressure drops below
8.7 psi (0,6 bar), and must
disappear when the pressure rises
above 22 psi (1.5 bar);

b - check that there are no water leaks

in the heating system.

Check:
a - that no obstructions are in the flue

discharge/air intake line

b - check the flue pressure switch

setting point, setting is 4.5 in.W.C

c - check that the electrical resistance

of the flue gas sensor corresponds
with the graph in section 13.14;

d - check that the electrical connection

cables between the flue pressure
switch, the flue sensor and the
power control board.

Replace the power control board

If the fan is powered with 163Vdc, replace the fan. If the
voltage to the fan is not 163 Vdc, replace the board.

a -If the heating pressure switch is not correctly set, it must

be replaced;

b - if the system has a leak, it must be fixed.

Filling of heating circuit
repeated 16 times in 24
hours

12.12.1 - Diagnostics: “L” lock-outs (continued)

L47

Flue pressure switch open
time longer than 60
minutes

a -If ther’is an obstruction, it must be removed;
b - If the flue pressure switch is not correctly set, it must be

replaced;

c - If the flue sensor resistance does not correspond, it must

be replaced;

d - if the electrical circuit is damaged, it must be repaired;

if the previous four cases do not apply, replace the power
control board

Содержание ONEX

















































































Результаты поиска

Содержание ONEX

Отзывы:

Похожие инструкции для ONEX

Бренды по названию

Популярные бренды

Embassy ONEX, Инструкция по установке и обслуживанию

Результаты поиска

Содержание ONEX

Отзывы:

Похожие инструкции для ONEX

Бренды по названию

Популярные бренды