Embassy ONEX Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 80

background image

58

13 - MAINTENANCE

13.1 - General
precaution

WARNING!!! Never store combustible
materials, gasoline or any product
containing flammable vapors and
liquids in the vicinity of the boiler.
Failure to comply with this warning
can result in extensive property
damage, severe personal injury or
death!

WARNING!!! Never obstruct the flow
of combustion and ventilation air.
Failure to provide adequate
combustion air for this boiler can
result in excessive levels of carbon
monoxide which can result in
severe personal injury or death!

CAUTION!!! Before

performing any maintenance
operations, shut the boiler off, close
the manual gas shut-off valve,
figures 16 and 17 item “3”, and shut
off electrical power to the boiler.
Follow the Operating Instructions
outlined in the section “SAFETY
INSTRUCTION”.

WARNING!!! If maintenance is
performed on the vent-air intake
system it must be properly
reassembled and sealed. Failure to
properly maintain the vent-air
system can result in excessive levels
of carbon monoxide which can
result in severe personal injury or
death!

WARNING!!! Servicing, inspection
and adjustment must be done by a
trained technician in accordance
with all applicable local and
national codes. Improper servicing
or adjustment could damage the
boiler! Failure to comply with this
warning can result in a fire or
explosion causing property damage,
personal injury or loss of life!

«
...
56
57
58
59
60
...
»

Содержание ONEX

















































































Отзывы:

Нет отзывов

Похожие инструкции для ONEX

Бренд: Nibe Страницы: 32

Бренд: IBC Страницы: 4

Бренд: VHH Страницы: 6

Бренд: Ideal Boilers Страницы: 72

Бренд: AEG Страницы: 72

Бренд: AEG Страницы: 120

Burnit PelleBurn 15

Бренд: Sunsystem Страницы: 68

Бренд: New Yorker Страницы: 64

Бренд: New Yorker Страницы: 32

Бренд: elco Страницы: 96

Brava One HE 25 ErP

Бренд: Sime Страницы: 68

Бренд: Vaillant Страницы: 40

Бренд: Vocera Страницы: 64

Бренд: Ideal Boilers Страницы: 72

Tube Steel Boilers

Бренд: Bryan Boilers Страницы: 8

initia MASTER 2.24 CF

Бренд: Chappee Страницы: 51

Potterton Precision

Бренд: British Gas Страницы: 60

Бренд: Hydro-Smart Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды