background image

P7    MAINTAINING YOUR FILTER 

1. Remove filter tank sealing O-ring.

2. With a clean cloth, wipe the lower filter body seal surface and clean seal of all dirt and debris. Do not use any 

solvent.

3. With a clean cloth wipe the upper body seal surface.

4.4.2 CLEAN SEAL RING AND SEAL SURFACE

Figure 5

Cartridge element 

Sealing O ring 

Bottom body

3. Carefully replace the cartridge over the hubs on the bottom manifold.

4. Place the upper body securely on top of the cartridge.

4.4.3 BODY AND LOCK RING RE-ASSEMBLY

1. Place the sealing O-ring on the bottom body. Place the upper body on the O-ring and the bottom body.

2. Use the EMAUX lock ring system only, tighten the lock ring (clockwise) until the latch is locked on position.

3. Ensure that upper and bottom bodies are properly secured with the lock ring. 

NOTE: DO NOT HIT OR STRIKE THE CLAMP WITH A HAMMER OR METAL TOOLS.

4. Ensure that the air relief valve assembly is in an OPEN position and no components are damaged or missing.

5. Ensure the drain plug is closed.

6. Open all system valves to allow water from the pool to the filtration system and from the filter to the pool.

7. Wait for the water to come out from the air relief valve then turn the air relief valve to fully CLOSE .

Upper body

Lock Ring

Sealing O-ring

Bottom body

Figure 6

Cartridge Element

4.4.4 VACUUMING POOL

Vacuuming can be performed directly into the filter whenever needed. 

Clean cartridge after vacuuming if required.

Содержание 9140401













Отзывы: