em-tec BioProTT FlowMCP Скачать руководство пользователя страница 74

Страница: 74 / 80

Technical Specifications of the BioProTT

FlowMCP (1-4 channels)

BioProTT™ FlowMCP (1-4 channels)

Operating principle

Ultrasonic Transit Time Flow Measurement (TTFM)

Device dimensions (HxWxD)

MCP1 and MCP2: 99 mm x 45 mm x 114.5 mm

MCP 4: 99 mm x 90 mm x 114.5 mm

Weight

MCP 1: 200 g | MCP 2: 240 g | MCP 4: 320 g

Housing Material

Polyamide

DINrail mounting type

Standard TS35 DINrail according to EN 60715; 35 x 7.5 mm

Supply voltage

24 V DC (± 10 %) supplied external. max. 2000 mA

Power consumption

typically 3 W; max. 8 W/9 W for BioProTT

FlowMCP4

Interfaces:

Interface types

1 x RJ 45

Protocol

Modbus TCP

Ambient Conditions:

Air pressure

70 kPa to 106 kPa

Operating altitude

up to 2000 m (6600 feet)

Operating temperature range

10°C to 40°C (50°F to 104°F)

Storage temperature range

–20°C to 45°C (-4°F to 113°F)

Transport temperature range

–20°C to 55°C (-4°F to 131°F)

IP Rating

IP20

Relative Air Humidity:

Operation

30 % to 75 % (non-condensing)

Storage and transportation

10 % to 96 % (non-condensing)

EMC:

The device was tested according to EN/IEC 61326-1, however, the

safety

safety of the overall system must be ensured by the customer.

BioProTT™ FlowMCP

Page 74

D214-703 BioProTT™FlowMCP – User Manual – V4.0

Содержание BioProTT FlowMCP

















































































Результаты поиска

Содержание BioProTT FlowMCP

Отзывы:

em-tec BioProTT FlowMCP, Руководство пользователя, Страница: 74 / 80

Результаты поиска

Содержание BioProTT FlowMCP

Отзывы: