background image

 

 

CMi6160 

User’s Manual English 

 

 

 

 

 

 

 

 

 

 

 

 

CMi6160 

User’s Manual English 

page | 29 (38) 

[2022-10] 

 

v1.4 

 

 

 

 

unsent such messages are sent each time (if for some reas

on the messages were not sent “last time”), 

so maximum transmitted messages per day is 4 (containing 4x6=24 readings, covering 2 days).

 

7.5 

Configuration options 

CMi6160 is configured via preconfigure service at delivery, via LwM2M device management or via the 
Elvaco OTC App, using NFC to transfer settings to the module. The Elvaco OTC App is downloaded via 
Google Play or at App Store for iOS. When the application has been installed, you can log in by using the 
user symbol in the top right corner. This will give you access to all your configuration profiles and enable 
you to configure any locked devices that have been claimed to your account. 
 
Table 9 through Table 13 provides a summary of all readable/writeable settings in CMi6160. Please note 
that the default configuration below is the one tailored for optimizing the performance of battery powered 
units. If changing these settings, the stipulated battery lifetime cannot be guaranteed.  
 
Device related configurations available in CMi6160: 

Parameter 

Description 

Configurable 
values 

Default 
value 
(battery)  

Device access 

– 

Locked device & 
correct PAK 

or

 

open device

 

Device access 

– 

No PAK

 

Meter ID 
 

Meter identification 
(secondary ID) for  
DIEHL Sharky/Scylar 

N/A 

N/A 

Readable 

Readable 

Power mode 

Activation status of 
the module. 

Passive, Active 

Passive 

Readable/ 
Writeable 

Readable 

Configuration 
Lock  

Locks the module to 
prevent unauthorized 
access. 

Open, Locked 

Open 

Readable/ 
Writeable 

Readable 

Synchronize 
meter time 

Used in OTC via NFC 
to use time of mobile 
phone to synchronize 
meter clock 

Used via App 

N/A 

Writeable  

Readable 

UTC offset 

UTC offset of the 
meter (in minutes). 

-720 - 720 

Readable/ 
Writeable 

Readable 

Max meter 
retries 

Maximum amount of 
quick retries when 
failing communicating 
with a meter 

0-255 

255 

Readable/ 
Writeable 

Readable 

Factory reset 

Resets the CMi6160 
to factory settings 
(default setting for 
power mode is 
Active)  

N/A 

N/A 

Writeable 

N/A 

Table 9: Device Related Configurations 

 

LwM2M-related configurations available in CMi6160: 

Parameter 

Description 

Configurable 
values 

Default 
value 
(battery)  

Device access 

– 

Locked device & 
correct PAK 

or

 

open device

 

Device access 

– 

No PAK

 

Bootstrap IP 

IP address of the 
bootstrap server the 
module will connect 
to upon activation. 

N/A 

84.19.147.
226  
(Elvaco 
Bootstrap 
server) 

Readable/ 
Writeable 

Readable 

Содержание 1100450







































Отзывы: