eltima electronic Jokie 2 Скачать руководство пользователя страница 6

Страница: 6 / 26

Quick Start

Quick Start

Getting started...

•

Insert four batteries or accumulators into the battery re-

tainer.

Please observe the correct polarity, which is shown

at the bottom of every battery compartment.

•

Put switch 2 of the mode switch to ON,

all others to OFF.

•

Turn the potentiometer left until the end

stop.

•

Install the light barrier and the 40mm reflector on one

tripod each.

•

Plug the DC-plug in the DC-plug of the light barrier.

this point the LED will shine green.

•

Plug the 2.5mm jack plug of the camera adapter unit

(adapter unit available as accessories) into the camera

socket.

•

Position the light barrier and the reflector opposite to

each other at a distance of 60 – 80 cm.

Note

: This distance is chosen randomly and it is

neither the shortest nor the largest possible dis-

tance between camera and reflector.

•

Align the infrared beam towards the reflector until the

LED goes out. The light barrier is ready for use now.

•

Plug the other end of the camera adapter unit into the

remote control socket of your camera.

•

Switch the auto focus of your camera to “manual“.

•

Move your hand or another object through the light

beam. The camera will be released.

Image 1: Battery case

Image 3: mode
switch

Image 4: Setup

ca. 60 – 80 cm

Image 2:
polarity marking

Содержание Jokie 2



























Результаты поиска

Содержание Jokie 2

Отзывы:

Бренды по названию

Популярные бренды

eltima electronic Jokie 2, Руководство пользователя

Результаты поиска

Содержание Jokie 2

Отзывы:

Бренды по названию

Популярные бренды