manualshive.com logo in svg

eltima electronic Jokie 2, Руководство пользователя

Поделиться
Скачать
eltima electronic Jokie 2 Скачать руководство пользователя страница 18

Taking pictures with Jokie²

Finding the midpoint of the reflector

Next you should look for the midpoint of the reflector and

direct the light barrier towards it. In order to do so, you

swing the light barrier slowly towards the right until the

LED is on again – please remember this point. Afterwards

you turn the light barrier left, until the light beam is be-

yond the reflector and the LED is on. The horizontal mid-

point is in the middle of these two points.
Now, starting from the horizontal midpoint, you also align

the light barrier towards the vertical midpoint. You will find

the latter as described above, only this time in the vertical

direction.

Connecting the camera

At this point the light barrier is aligned, so that you can

connect the camera. After that the system is prepared and

ready to take pictures – the camera will be released if the

light beam is interrupted.

Important camera settings

Auto-focus

When photographing with light barriers it is mandatory to

switch the auto-focus of the camera to manual. By not do-

ing this, the camera will probably not release.

This principle applies for all operating modes of the light

barrier.
Reason:   The   auto-focus   is   too   slow   for   the   most   high-

-speed situations, even though now days systems are al-

ready very fast. The light barrier replaces the auto-focus!
Focus the lens to a point were you expect that your sub-

ject may be, when the camera takes the picture. The sub-

jects speed, the moving direction as well as the cameras

lag time must be taken in account.
According to the speed and the lag time of the camera, the

subject will travel a certain distance away from the beam.

The right focus point has to be determined by a number of

trials.

18

© eltima electronic 2013

Содержание Jokie 2



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды