eltima electronic Jokie 2 Скачать руководство пользователя страница 5

Страница: 5 / 26

Introduction

Introduction

Dear client,
thank you for purchasing our light barrier

. For you,

being an ambitious photographer, it shall be a reliable tool

that is both handy and easy to operate.
Please do not hesitate to contact us if you should miss

anything or have further improvement proposals. Only like

this the product will be able to develop to fully meet your

requirements.
Please read this manual carefully before using the light

barrier. It is supposed to get you familiar with operating

the system and all its functions. In this way you will be
able to use all the advantages

offers.

Intended purpose

This light barrier

was solely built to release photo-

graphic cameras, flashes and filming devices. Please do

only use it for this purpose!

Symbols

Symbol for tips concerning the handling of the de-

vice.
Important advice concerning the function of the de-

vice.

Important advice to prevent damage of the device or

connected devices.

Maintenance and storage

•

is not waterproof and therefore neither suitable

for use in rain nor under water. Please contact the man-

ufacturer immediately in case it should get wet. Water

drops can be wiped off with a dry cloth.

•

Do not drop it or expose it to shocks.

•

This device is a precise electrical/optical system. Do not

try to make alterations yourself.

•

Please remove the batteries in case you should not use

the device for some time. This will prevent any leaking

of the batteries.

•

Please clean the lenses occasionally with a soft cloth.

Содержание Jokie 2



























Результаты поиска

Содержание Jokie 2

Отзывы:

Бренды по названию

Популярные бренды

eltima electronic Jokie 2, Руководство пользователя

Результаты поиска

Содержание Jokie 2

Отзывы:

Бренды по названию

Популярные бренды