Elka EST 4004K Скачать руководство пользователя страница 9

© 27.04.2005 ELKA-Torantriebe GmbH u. Co. Betriebs KG                     Page 9  

                                   EST 4004K 

 

Automatic closure for partial (pedestrian) opening. 

DIP A5 OFF 

Automatic closure is off. 

 

DIP A5 ON 

Automatic closure for the pedestrian position is enabled. 

If the gate is at the pedestrian position, BTG restarts the time to stay open. The gate opens 

completely if BA1 or BA2 is pressed. The gate closes immediately if BT or BZ is pressed. 

 
 
 

 
Automatic closure for completely open. 

DIP A6 OFF 

Automatic closure is off. 

 

DIP A6 ON 

Automatic closure from the open position is enabled. 

 

If the gate is in open position BA1 or BA2 restart the time to stay open. The gate closes 
immediately if BT or BZ are pressed when the gate is open. The gate reopens if BT is 
pressed during closing. 

 
 
 

 
Warning prior to opening 

DIP B1 OFF 

No warning. 

 

DIP B1 ON 

The warning light is switched on 4 seconds before the gate opens. 

 
 
 
 
Warning prior to closing 

DIP B2 OFF 

No warning. 

 

DIP B2 ON 

The warning light is switched on 4 seconds before the gate closes. 

 
 
 

 
Locking relays / Dead man’s button 

DIP B3 OFF 

The control box works with locking relays. 

 

DIP B3 ON 

BA1, BA2 and BZ are dead man’s buttons. (The opener stops as soon as the button is 
released). 

 
 
 

 
Delayed closing 

DIP B4 OFF 

The opening gate closes immediately when BZ is pressed. 

 

DIP B4 ON 

If the gate is opening and BZ is pressed, the signal is stored until the gate is open and then 
carried out. 

 
 
 

 
Three-phase operation

 

DIP B5 OFF 

Drive with single-phase motor (with electronic brake) 

DIP B5 ON 

Three-phase motor (with reversing contactor and mechanical brake) 

 
 
 

Содержание EST 4004K















Отзывы: