Elk Products EZ8 ELK-M1EZ8 Скачать руководство пользователя страница 46

Страница: 46 / 68

M1EZ8 Installation and Programming

Page 46

123456789012345678901234567890121234

WZnxxx:Sel

Prg

Wireless Zone

1234567890123456789012345678901212345

WZnxxx 01:=No

Enable Transmitr

1234567890123456789012345678901212345

WZnxxx02:=0

Supervision Type

1234567890123456789012345678901212345

WZnxxx 03:=No

Enable Option 1

1234567890123456789012345678901212345

WZnxxx 04:=No

Enable Option 2

123456789012345678901234567890121234

WZone = xxx

TransmtToEnroll

1234567890123456789012345678901212345

4:KeyfobSel

Prg

Event Definition

123456789012345678901234567890121234

Keyfob Button=1

1000=Event

1234567890123456789012345678901212345

2:Xmit Sel

Prg

Transmitter Opt

1234567890123456789012345678901212345

3:Learn Sel

Prg

WirelessTransmtr

123456789012345678901234567890121234

WZone = xxx Push
TransmiterButton

1234567890123456789012345678901212345

WZnxxx 05:=001

Keyfob User ID

Press the RIGHT arrow key to select 2:Xmit Transmitter Opt.

Use the UP and DOWN arrow keys to locate a particular wireless transmitter. Press
the RIGHT arrow key to select and program the displayed transmitter.

This selection determines whether or not the transmitter is enabled. Whenever you
enroll a new transmitter this location will be automatically set to Yes. To permanently
or temporarily disable this transmitter program this to No.

This selection determines the “Supervision Type” for the transmitter. 0=No Supervision,
1=Regular Supervision, 3=Fire Supervision. See receiver selections R02 and R03 for
supervision time values. Default is 1.

This selection corresponds to the

Caddx Transmitter Option 1

which deals with

enabling or disabling the internal reed switch on the individual Caddx transmitter so
that an external switch may be hardwired to the transmitter.

Refer to the Caddx NX

Series Receiver Instructions, Option 1, for complete details.

This selection corresponds to the

Caddx Transmitter Option 2

which deals with

whether an external switch should be normally open (N/O) or normally closed (N/C).
For N/O set option to No. For N/C set option to Yes.

Refer to the Caddx NX Series

Receiver Instructions, Option 2, for complete details.

If the transmitter is a keyfob, this sets the User ID to be logged when the keyfob is
used to arm or disarm. Valid range is 001 to 255. Numbers 001 to 199 mirror the
keypad user codes. To report an open/close from a keyfob, program the corresponding
keypad user code to report. A report will be sent regardless of whether it was a user
code or a keyfob that armed/disarmed the system. NOTE: Since there are no open/
close report codes beyond user 199, any keyfob ID that is set higher that 199 will
utilize the opening/closing report code for User 199.

Press the RIGHT arrow key to select 3:Learn Wireless Transmitters.

Press the UP or DOWN arrow keys to locate the wireless zone that you wish to enroll.
Then press the RIGHT arrow key to continue.

Go to the transmitter and press the tamper or enroll button. The keypad should emit a
short tone when the transmitter becomes enrolled.

Press the RIGHT arrow key to select 4:Keyfob Event Definition

Press the UP or DOWN arrow keys to locate the keyfob button to program. There are
a total of 8 programmable buttons, however only 6 of the 8 may be used on the keyfob.
The valid activation events programmable for each button ranges from 0000-0030
(utilizing the Zone Definitions table) and 2001-2032 (utilizing Appendix A, Event Codes).

The standard buttons are as follows: Button 1 (Lock), 2 (Unlock), 3 (Light), and 4
(Asterisk). For Button 7 press a combination of buttons 1 & 2 together at the same
time. For Button 8 press a combination of buttons 3 & 4 together at the same time.

Button 3 on a keyfob can be changed to 5 by setting the transmitter Option 1 to Yes.
Button 4 on a keyfob can be changed to 6 by setting the transmitter Option 2 to Yes.