background image

ELK-M1XEP 

v2

  Installation Manual

Page 3

FEATURES:

 Secure connection with password protection and SSL/TLS encryption

 

Flash Memory for Firmware Updating

 Event notification via E-Mail (SMTP)

 Supports automatic Dynamic DNS Updates with providers using the DynDNS protocol.

 Supports Network Time Protocol for synchronizing the M1/EZ8’s clock with an Internet time server.

 Internet Monitoring and Reporting Capability

 Network stack supporting the following protocols:

   TCP,UDP,DHCP,SSL/TLS, NTP, SMTP

 

Federal Information Processing Standards (FIPS) 128 bit encryption

 Integrated 802.3 compliant 10/100 Mbit network interface

 RS232, DB9M 9-pin serial port connection

 Connects to the M1 RS-232 Serial port 

(Port 0).  The baud rate for this port must be set to 115,200 (factory default)

 RJ45 8-pin Network Jack

 2.1mm barrel type power connector (center positive)

 LED Indicators for Power, Link, and Data

SPECIFICATIONS:

 Operating Voltage: 12 Volts D.C. from Elk-P1216 Plug-in Power Supply **

 Current Draw: approx. 300 mA

 Housing Dimensions: 4.25" x 6.375" x 2.125"

 Circuit Board Dimensions: 2.25" x 3.95"

**   The M1XEP may be powered from a different 12VDC power source.  A 2.1 mm barrel type 

connector is required for the power connection and the center of the barrel connector 

must be positive (+).

Any required network equipment, i.e. Ethernet switch, router, cable modem, etc. including 

the plug-in power supply for the M1XEP, MUST be backed up with an adequately sized UPS 

(Uninterruptible Power Supply) in order for the equipment to continue operating during 

brief power outages. 

The non-secure port in the M1XEP is intended for use within the LAN ONLY.  Only devices 

on the local network (behind the network router) should connect to this port.  We strongly 

discourage port forwarding the non-secure port outside the LAN.  

Features and Specifications

APPLICATION:

The 

ELK-M1XEP 

is an Ethernet Appliance with a RS-232 Serial Port Interface.  It may be used to connect a control in 

the M1 Family to an Ethernet network.  It features email event notification and FIPS compliant encryption algorithms for 

security sensitive environments.  It is powered by an ELK-P1216 12 Volts DC, 1.5 Amp plug-in power supply/adapter.  A 

software setup utility is built into ElkRP for configuring the connection setup, network password, etc.  The M1 Ethernet 

Interface is factory defaulted to obtain a dynamic IP address from a DHCP server (i.e. router, cable modem, etc.).  It may 

optionally be setup with a static IP address.  

Содержание ELK-M1XEP

























Отзывы: