background image

5. 

Before fitting the unhanded door post, offer the glass panels to the door (see glazing plan in 
booklet for glass size guide on door), slide them in from the side. Carefully attach the unhand-
ed door post in the same way as before, ensuring the glass is sitting in the correct position 
(sitting on the beading channels of the door posts) before tightening the screws. 

 

6. 

Make sure all angles are square 

 

and tighten all screws. Now insert 

 

2 glazing clips to the glass on the 

 

unhanded door post.  
The other side of the door is 
clipped using a pvc glass strip (or 
clip cap). Cut the strip to the correct length and push into the cavity between the glass and the 
handed door post. The cap when fitted acts as a wedge to prevent movement of the glass. Met-
al clips are not fitted to this bar. 

 
7. 

Fix each door wheel into position by pushing the bolt provided through the centre of the 

 

wheel and then through the hole in the top door panel from underneath (i.e. from the inside of 

 

the door). Put the washer over the bolt and secure with the nut provided, tightening until there 

 

is no movement on the bolt. The nuts are lock-nuts and are harder to put on than normal nuts 

 

in general assembly. The wheel will revolve freely because it has ball bearings in it. 

The 

 

wheel has a collar protruding from the centre, this collar goes against the inside face of 

 

the top door panel. (See picture below).

 

 

8. 

Slip the nylon door skids on each of the bottom panels. This may already have been done pri

 

or to delivery. After fitting the doors (see later in the booklet), you may need to lower the 

 

door skid so that it engages with the bottom door cill to allow smooth movement of the door. 

 

Lower the skid on each door and insert a self tapping screw at each end of the skid to rein

 

force the position. 

 

9. 

Build the right hand door using the remaining handed and unhanded door post. Viewed from 

 

the outside, the handed door post will be on the left of the door, while the unhanded door post 

 

will be on the right. At this point you must decide the height you would like your door lock. 

 

The hole to take the door lock is on the left hand side of the infill panel. You can decide to fit 

 

this panel to the 2nd or 3rd panel down. 

Make sure you fit the glass before final fixing of 

 

the door. 

See glazing plan towards the back of this booklet 

 
10.  Thread the stainless steel backed brush 
 

extruder into the PVC carrier. This may 

 

already have been done prior to delivery 

 
11.  Turn the doors over and insert the black 

brush draught excluder in the groove (bolt 
slot) in the unhanded door posts. Insert a 
nut and bolt at the bottom of each un-
handed door post and tighten so that the 
brush will not slip down when the door is 
in its upright position,  Cut off the surplus 
brush and carrier at the top of the bar 

 

12.  Do not fit the door to the gable at this 

stage – wait until the structure is fully 
assembled prior to glazing. 

13.  Door handles can now be fitted. 

Содержание 4'3" wide compact





























Отзывы: