manualshive.com logo in svg

Elgo LIMAX Safe SC, Руководство по эксплуатации

Поделиться
Скачать
Elgo LIMAX Safe SC Скачать руководство пользователя страница 37

 
 

 
 

 

 

Installation 

 

- 37 - 

 

Figure 17: Connection of door zone indicator 

Table 9: Wire assignment door zone indication 

Pin on S99  Wire colour on 

PIO

 cable  Function 

14 

white-yellow 

DZ-SUP (Door zone indicator supply) 

15 

yellow-brown 

DZ (Door zone indicator output) 

8.3.14

 

Connection CAN bus 

The LIMAX Safe SG/SC CAN bus connection CAN High and CAN Low is connected to the CAN bus of the con-
trol. The shield may be optionally connected to protection earth on the side of the lift control. See Figure 14 for 
further details. 

Table 10: Wire assignment CAN 

Pin on S99  Wire colour on PIO cable  Function  

3 

yellow 

CAN HIGH 

4 

green 

CAN LOW 

5 

- 

shield 

8.3.15

 

Connection of earthing connector  

The LIMAX33 RED/LIMAX44 RED sensor and the Safe Box have both an earthing lug. These lugs need to be 
connected with protection earth via a suitable earth cable. The earth cable should be equipped with a suitable 
flat plug for connection to the earthing connector. The earth cables for the LIMAX33 RED/LIMAX44 RED sensor 
and for the Safe Box should be comparable in terms of cross-section, material and length. Ideally an identical 
cable with a recommended cross-section of 4 mm² is used for the box and the LIMAX 33 RED. This is not in-

cluded in the scope of delivery but can be ordered as an accessory. 

To connect the earth cable to the earthing lug, the cable is provided on one side with a flat plug sleeve and on 
the other side with a ring cable lug for placing on the protection earth. 

Note: For protection against electrical shock, a cable with 0.75 mm² would be sufficient, but to optimize the 
immunity to interference, 4 mm² is recommended. 

The shield for the CAN bus is connected on the device side via the housing to protection earth. If it can be en-
sured that there is a protection earth on the control side, in which no potential differences can occur to the con-
tact point of the device-side protection earth, and thus no ground loops are formed, the shield must also be 
connected to the protection earth on the control side. This is an ideal solution for optimal interference suppres-
sion.  

 
If the ground loops cannot be excluded with certainty, the shield must not be connected on the control side in 
order to avoid EMC-induced faults of the operation. 

Safe Box

DZ-SUP

DZ

+12 V battery

GND

Содержание LIMAX Safe SC





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды