5.3 Connection example VariEasy SH 230 V / 50 Hz
1 0 2
reseau electrique
L
N
PE
230V/50Hz
ver
t-j
aune
br
un
no
ir
ble
u
de volet
M
1~
1 0 2
rete
L
N
PE
230V/50Hz
ver
de
/g
ial
lo
m
ar
rone
ner
o
blu
M
1~
1 0 2
Netz
L
N
PE
230V/50Hz
gr
ün/
gel
b
br
aun
sc
hw
ar
z
bla
u
oder -taster
M
1~
1 0 2
power grid
L
N
PE
230V/50Hz
gr
ee
n/
Yel
low
br
own
bl
ac
k
blu
e
junction box
M
1~
boiter de
scatola di
derivatione
Fig. 5 Diagram VariEasy SH 230 V / 50 Hz
Check for functioning: If necessary, change or swap the
assignment of the direction buttons for the operating switch/
push button.
Important
The drive control in travel direction UP or DOWN/CLOSED
must be interlocked. A reversing delay of at least 0.5 sec-
onds must be ensured.
Due to feedback voltage from the installed capacitor, never
connect several drives in parallel.
5.4 Adjustment of the end positions
Important
The two interior limit switch adjustment screws for the upper
and lower end position are assigned based on the parallel
position of the rotating crown to the limit switch with the
printed running direction arrow.
Upper end positions (position 0) or
lower end positions (position 1)
Fig. 6 End positions
10 rotations of a limit switch adjustment screw causes 1 ro-
tation of the winding shaft.
►
Turning a limit switch adjustment screw from negative [-]
to positive [+] increases the travel path of the blind.
►
Turning a limit switch adjustment screw from positive [+]
to negative [-] reduces the travel path of the blind.
The end positions are set using the elero mounting cable.
ATTENTION
The limit switch only functions if the drive has been installed
properly in a winding shaft (profile tube or round tube).
5.4.1 Upper end position (position 0)
►
Allow the drive (without blind) to run fully in
DOWN/CLOSED direction.
►
Attach the rolled-down blind to the winding shaft.
►
Press and hold down the [
UP ▲
] button and hold it down.
►If the drive switches off before it reaches the desired
end position, turn the corresponding interior limit switch
adjustment for the upper end position (see Chapter 5.4.3)
towards positive [+] until the desired blind position has
been reached.
►If the drive does not switch off automatically when the
desired end position has been reached, release the UP
button. Run the blind a short distance in the other direc-
tion. Turn the interior end switch adjustment screw for the
upper end position in the negative [-] direction and move
back to the end position. Repeat this process until the
desired end position has been reached.
5.4.2 Lower end position (position 1)
►
Push the [
DOWN/CLOSED
▼
] button and hold it down.
►If the drive switches off before it reaches the desired
end position, turn the corresponding interior limit switch
adjustment for the lower end position (see Chapter 5.4.3)
towards positive [+] until the desired blind position has
been reached.
►If the drive does not switch off automatically when the
desired end position has been reached, release the
DOWN/CLOSED button. Run the blind a short distance
in the other direction. Turn the interior end switch adjust-
ment screw for the lower end position in the negative [-]
direction and move back to the end position. Repeat this
process until the desired end position has been reached.
5.4.3
Different installation situations
To adjustment the upper or lower end position of the blind,
use the adjusting tool or another suitable tool to operate the
corresponding interior screw (indicated in black in the figure).
Before readjusting an end position, move the blind out of
the current end position.
Cable outlet on the left of the drive
³
´
³
´
³
´
5XQGNRS
I
6WHUQNRS
I
5XQGNRS
I
6WHUQNRS
I
5XQGNRS
I
6WHUQNRS
I
5XQGNRS
I
6WHUQNRS
I
³
´
³
´
³
´
³
´
³
´
³
´
³
´
³
´
5XQGNRS
I
6WHUQNRS
I
5XQGNRS
I
6WHUQNRS
I
5XQGNRS
I
6WHUQNRS
I
5XQGNRS
I
6WHUQNRS
I
³
´
³
´
³
´
³
´
³
´
©
elero
GmbH
EN | 5
Adjustment of the end positions
