background image

14. SETTINGS MENU 

71

14.2.1 RENAME

 

Opens a screen where you can rename the active song.

14.2.2 CLEAR

 

Clears the active song 

14.2.3 LOAD

 

Opens a screen where you can select and load songs 

14.2.4 SAVE TO PROJ

 

Saves the active song to the project.

14.3 PATTERN

Use the PATTERN menu to perform pattern management. Use the 

[UP]

 and 

[DOWN]

 arrow keys to move 

between the options. Press 

[YES]

 to confirm your selection. Exit the menu by pressing 

[NO]

.

14.3.1 RENAME

Opens a NAMING screen where you can rename the active pattern. For more information, please see 

“7.8 THE NAMING SCREEN” on page 22.

14.3.2 CLEAR

• WHOLE PATTERN

 Clears the active pattern’s sequencer data and kit. A prompt appears when you 

select this option. Press 

[YES]

 to clear, or 

[NO]

 to cancel the operation. Note that no pattern informa-

tion will be permanently lost until the pattern is saved to the same pattern slot that it was loaded from.

• KIT DATA

 Clears all the sounds of the active pattern. All sequencer data will remain unchanged. A 

prompt appears when you select this option. Press 

[YES]

 to clear, or 

[NO]

 to cancel the operation. 

Note that no kit information will be permanently lost until the pattern is saved to the same pattern slot 

that it was loaded from.

• SEQUENCE DATA

 Clears the active pattern’s sequence data. All sounds will remain unchanged. A 

prompt appears when you select this option. Press 

[YES]

 to clear, or 

[NO]

 to cancel the operation. 

Note that no sequencer information are permanently lost until the pattern is saved to the same pattern 

slot it was loaded from.

14.3.3 SAVE TO PROJ

You must have saved the project at least once before you can save pattern information.

• WHOLE PATTERN

 Saves the active pattern’s sequence data and kit to the +Drive. A prompt appears 

when you select this option. Press 

[YES]

 to save, or 

[NO]

 to cancel the operation.

• KIT DATA

 Saves the active pattern’s kit to the +Drive. A prompt appears when you select this option. 

Press 

[YES]

 to save, or 

[NO]

 to cancel the operation.

• SEQUENCE DATA

 Saves the active pattern’s sequence data to the +Drive. A prompt appears when 

you select this option. Press 

[YES]

 to save, or 

[NO]

 to cancel the operation. 

Содержание Syntakt























































































































Отзывы: