Elektron Syntakt Скачать руководство пользователя страница 54

Страница: 54 / 118

10. AUDIO TRACK PARAMETERS

Press

[LFO]

to access this parameter page.

10.8.1 SPD

Speed sets the speed of the LFO. Try settings of 8, 16 or 32 to sync the LFO to straight beats. The knob

is bipolar. The LFO cycle can be played backward by using negative values.

10.8.2 MULT

Multiplier multiplies the SPD parameter by the set factor either by multiplying the current tempo (BPM

settings), or by multiplying a fixed tempo of 120 BPM.

10.8.3 FADE

Fade In/Out makes it possible to fade in/fade out the LFO modulation. The knob is bipolar. Positive val-

ues give a fade-out, negative values give a fade in. 0 gives no fade in/fade out.

10.8.4 DEST

Destination selects the modulation destination for the LFO. Preview how the LFO modulation will affect

the sound by highlighting a destination. Press

[YES]

to confirm the selection. For more information,

please see “APPENDIX C: LFO MODULATION DESTINATIONS” on page 112

10.8.5 WAVE

Waveform sets the LFO waveform. The Triangle, Sine, Square, Sawtooth, and Random waveforms are

bipolar. The Exponential and Ramp are unipolar.

10.8.6 SPH

Start Phase sets the point within the wave cycle where the LFO will start when it is trigged. 0 makes the

LFO start at the beginning of a complete wave cycle, 64 makes it start at the center. A small square at

the start of the waveform shows that the wave cycle starts at a zero-crossing point.

10.8.7 MODE

Trig Mode sets how the LFO will act when a note is trigged.

• FRE

is the default free-running mode. It makes the LFO run continuously, never restarting or

stopping even if notes are trigged.

• TRG

makes the LFO restart when a note is trigged.

• HLD

makes the LFO run free in the background, but when a note is trigged the LFO output level is

latched and held still until the next note is trigged.

• ONE

The LFO starts when a note is trigged, then runs to the end of the waveform and then stops.

This makes the LFO function similar to an envelope.

• HLF

The LFO starts when a note is trigged, then runs to the middle of the waveform and then stops.

10.8.8 DEP

Depth sets the depth and polarity of the LFO modulation. Both negative (inverted) and positive modula-

tion depth is possible. A setting of 0 equals no modulation depth.

10.9 LFO PAGE 2

LFO page 2 page contains the same parameters as LFO page 1, but controls the behavior of LFO 2. It is

possible to also use LFO2 to modulate LFO 1’s parameters Press

[LFO]

twice to access this parameter page.

Содержание Syntakt























































































































Результаты поиска

Содержание Syntakt

Отзывы:

Похожие инструкции для Syntakt

Бренды по названию

Популярные бренды

Elektron Syntakt, Руководство пользователя

Результаты поиска

Содержание Syntakt

Отзывы:

Похожие инструкции для Syntakt

Бренды по названию

Популярные бренды