19
EN
Operating and assembly instructions HRD
www.elektror.com
9016309 01.20/13
• Move the motor including support
fl
ange plate towards the
support
fl
ange housing.
• Remove the faulty V-belt (26).
• Check the V-belt pulleys
(they must be free from burrs, rust and dirt).
• Fit the new V-belt loosely by hand.
• Pay attention to exact alignment of the V-belt pulleys.
• Set the belt tension as per the label using a hexagon
bolt (58).
• Tighten the hexagon bolt (60) or
fi
xing bolt on the motor
tensioning rail (43).
• Attach the grating (55) or belt guard (27).
You will
fi
nd the data applicable to your appliance with V-
belt drive indicated on the label a
ffi
xed to the support
fl
ange
plate. They are also tabulated in section 11 of these Operat-
ing and Assembly Instructions.
5.5 Cleaning
There is a high risk of injury on the inside of the device due to
rotating parts during operation. Decommission the device in
all cases and wait until all moving parts have stopped before
opening, reaching in or inserting tools into the device. Secure
the device reliably against it being accidentally restarted dur-
ing the entire period.
Also make sure that no other dangerous situation can arise
when restarting after a standstill, e.g. as a result of a power
failure or blockages.
Cleaning or maintenance must not lead to damage or modi-
fi
cations to the device and its components that would in
fl
u-
ence safety or health protection and, for example, impair the
balanced state of the impeller.
When starting up the blower, make sure that all tools or other
foreign objects have been removed from inside the device
and that all covers and protective grilles have been attached
correctly.
6 SAFETY RELATED INFORMATION
ON TAKING OUT OF OPERATION AND
REMOVAL
The disconnection of all electrical connections and any other
electrical work in connection with decommissioning must
only be carried out by a quali
fi
ed electrician.
The device should be dismantled only when all rotating parts
have come to a standstill and cannot be restarted.
The guidelines set out in 2.1 Transport and Handling must be
observed when dismantling and removing it.
Treat the device as industrial waste when disposing of it.
The device parts are made of recyclable material, such as
aluminium, (stainless) steel, copper and plastic. However,
there are components that need special treatment (e.g. fre-
quency converters). The statutory national and local disposal
and recycling regulations must be observed.
7 LIABILITY AND EXCLUSION OF
LIABILITY
The owner shall bear the responsibility for the correct use of
the device.
Elektror shall not accept any liability for any use of its prod-
ucts and components which is contrary to their intended use.
This shall also apply in particular to use in special applica-
tions and under operating conditions that have not been spe-
ci
fi
cally agreed with Elektror.
Elektror shall not accept any liability for any modi
fi
cations or
alterations to the device or accessories supplied.
Likewise, Elektror shall not be liable for improper, delayed,
neglected maintenance. Neither shall it be liable for any
cleaning and repair work not carried out by quali
fi
ed Elektror
specialists, nor for the possible consequences.
Содержание HRD 1/2T
Страница 21: ...21 www elektror de Betriebs und Montageanleitung HRD 9016309 01 20 13 DE...
Страница 37: ...37 www elektror de Betriebs und Montageanleitung HRD 9016309 01 20 13 DE...
Страница 38: ...38 Betriebs und Montageanleitung HRD www elektror de 9016309 01 20 13 DE...
Страница 39: ...39 www elektror de Betriebs und Montageanleitung HRD 9016309 01 20 13 DE...