Electrolux T5190LE Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 118

background image

Service Manual

99

22:92 NO OVERHEAT INT.

Warning: The Motor Control Unit indicates A.nOHI.
Overheat internal is reset. See also error code 22:87.
Internal message 92.
Recommended actions:

1. Restart the machine.

22:93 BUS

Warning: The Motor Control Unit indicates A.buS.
Timeout of monitoring time of communication between bus operator and inverter (Watchdog).
Internal message 93.
Recommended actions:

1. Switch off the main power to machine for 5 minutes.
2. Restart the machine.

22:94 PROTECT. ROT. FORWARD

The Motor Control Unit indicates error A.PrF.
Forward (right) limit switch is activated. Not used in this application.
Internal message 94.

22:95 PROTECT. ROT. REVERSE

The Motor Control Unit indicates error A.Prr.
Reverse (left) limit switch is activated. Not used in this application.
Internal message 95.

22:96 DRIVE OVERHEAT

Warning: The Motor Control Unit indicates A.dOH.
Motor temperature too high. Can only be reset when motor temperature has dropped (Resistance at terminals T1/T2
> 1650 Ω) This is indicated by message A.ndOH. See also error code 22:91.
Internal message 96.
Recommended actions:

1. Switch off the mainpower for 30 minutes until motor has cooled down.
2. Restart the machine. If problem persists, check motor windings etc.

22:97 MOTOR PROTECTION

Warning: The Motor Control Unit indicates A.OH2.
Electronic motor protection relay has tripped.
Internal message 97.
Recommended actions:

1. Switch off the main power to machine for 5 minutes.
2. Restart the machine.

22:98 NO OVERLOAD

Warning: The Motor Control Unit indicates A.nOL.
Overload counter is reset to 0%. See also message 22:99.
Internal message 98.
Recommended actions:

1. Restart the machine.

«
...
97
98
99
100
101
...
»

Содержание T5190LE























































































































Отзывы:

Нет отзывов

Похожие инструкции для T5190LE

Бренд: Steba Страницы: 52

Бренд: Valentine Страницы: 5

Бренд: Sierra Страницы: 25

Instant Recovery 18 TS

Бренд: Keating Of Chicago Страницы: 2

Бренд: Gourmia Страницы: 20

Бренд: GGMgastro Страницы: 9

Easy Fry Compact digital

Бренд: T-Fal Страницы: 31

Performance MEDE250

Бренд: Maytag Страницы: 2

Бренд: Optimum Страницы: 45

Бренд: Waring Страницы: 11

Бренд: Taurus Страницы: 60

Бренд: GE Страницы: 144

NA-S086M4 Series

Бренд: Panasonic Страницы: 33

Бренд: Electrolux Страницы: 26

Бренд: Electrolux Страницы: 15

Бренд: Electrolux Страницы: 21

Бренд: Electrolux Страницы: 24

Бренд: Electrolux Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды