Electrolux T5190LE Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 118

background image

70

Service Manual

13.3 Description of error codes and causes

MAIN COMMON

10:1 INTERNAL ERROR CPU TACHO

Tacho input on CPU delivers values that is out of range.
Recommended actions:

1. Run motor on highest possible speed in service mode. Check input value for RPM speed.
2. Replace defective component.

10:11 REAL TIME CLOCK OUT OF ORDER

The real time clock is used by the control system for delayed start, measuring time, power failure, error codes, etc.
Upon power on, the communication with the internal real time clock in the control system is established. In case this
fails, this error occurs
Recommended actions:

1. Power off the machine for 1 minute and try again.

10:13 INITIALIZATION FAILED

The error code is shown if the hardware initialization has failed to initialize within 15 seconds after power on.
Recommended actions:

1. Press the control knob/start button to retry.
2. Upload a new software that matches the machine configuration and try again.

10:15 MACHINE STOP

This message is shown if input for

MACHINE STOP

is activated.

This is not an error code but is handled in the same way.
Recommended actions:

1. Reset the Machine Stop Button.
2. Press the control knob to confirm machine stop. Machine will revert to Idle mode.

10:16 EMERGENCY STOP

This message is shown if input for

EMERGENCY STOP

is activated. This is not an error code but is handled in the same

way.
Recommended actions:

1. Reset the Emergency Stop Button.
2. Press the control knob to confirm emergency stop. Machine will revert to Idle mode.

«
...
68
69
70
71
72
...
»

Содержание T5190LE























































































































Отзывы:

Нет отзывов

Похожие инструкции для T5190LE

Бренд: Samsung Страницы: 7

Бренд: Samsung Страницы: 12

Бренд: T-Fal Страницы: 16

Бренд: Maytag Страницы: 40

StarlettePlus-E

Бренд: Parker Страницы: 148

Бренд: Maestro Страницы: 48

Бренд: Kalorik Страницы: 24

Бренд: Smeg Страницы: 32

Бренд: Tescom Страницы: 28

Бренд: Presto Страницы: 6

Бренд: Saivod Страницы: 84

Бренд: Maguire Products Страницы: 92

Бренд: Hoover Страницы: 32

Бренд: Lagrange Страницы: 44

Artist Magic Cord

Бренд: OBH Nordica Страницы: 28

Бренд: Taurus Страницы: 60

Бренд: Truvox Страницы: 8

Бренд: Haier Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды